Pistons and Connecting Rods - Remove
开始:
- 拆卸缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
- 拆下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查连杆和连杆盖 (2) 上的识别标记是否正确。 连杆和连杆盖 (2) 朝向发动机右侧的那一侧应带有蚀刻编号。 该编号必须与气缸号一致。 轴承挡圈凹口也应在右侧。 如有必要,标记连杆和连杆盖 (2)。
- 拆下连杆盖螺栓 (1) 和连杆盖 (2)。 从连杆盖 (2) 上拆下连杆轴承下轴瓦。
Show/hide table
图 2 g01064123 - 推动活塞和连杆 (3) 远离曲轴。 拆卸连杆轴承 (4) 的上半部分。
- 从缸体上拆下活塞和连杆 (3)。
- 对于其余的活塞和连杆,重复步骤 1 至 4。
Show/hide table
图 1 | g01064122 |
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
G3300 Engines Valve Data Sheet
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pan - Remove and Install
3406E Truck Engine Vibration Damper
G3300 Engines Ignition System Timing - Check/Adjust
3406E On-Highway Engine Inlet and Exhaust Valve Seals - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3612 and 3616 Engines Compression Release Valve
3116 and 3126 Marine Engines Reference Material
G3300 Engines Engine Crankcase Breather - Clean
3116 and 3126 Marine Engines Refill Capacities
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Engine Oil Pump - Install
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
3406C (PEEC III) Truck Engines General Information
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3406E On-Highway Engine Fuel Filter Base - Remove and Install
3114, 3116, and 3126 Industrial and Generator Set Engines Engine Crankcase Breather - Clean
C-18 Truck Engines Compression Brake - Inspect/Adjust/Replace
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Main Bearings - Remove