Engine Oil Pan - Remove and Install
Show/hide table
热油和热的部件可能会导致人身伤害。 不要让热油或热的部件与皮肤接触。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 将发动机机油排入合适的容器以便保存或弃置。
Show/hide table
图 1 g00516290 典型示例 - 拆下螺栓 (2) 和垫圈。 拆下降噪盖 (1)(如有配备)。
Show/hide table
图 2 g01022237 典型示例 - 拆下缸体上的下列零件:螺栓 (5)、垫圈、隔离器和隔离器套管。
- 拆下发动机油底壳 (6) 和垫片。
- 必要时拆下管道螺塞 (3) 和排放螺塞 (4) 以及 O 形密封圈。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | - | |
(-) | Loctite 5900 | - | |
B | - | Loctite 243 | - |
C | - | Loctite 243 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检验密封垫的状况。 必要时,更换垫片。
- 清理发动机油底壳和缸体的配合面。
注: 安装前,将工具 (A) 涂抹到缸体边缘和接缝处。
Show/hide table图 3 g01022237 典型示例 - 在缸体上安放一个密封垫和发动机油底壳 (6)。
- 安装下列项:隔离件套筒、隔离件、螺栓 (5) 和垫圈。
注: 执行下列步骤以便消除从发动机油底壳螺栓漏油的可能性:
- 清洁及干燥螺栓孔。
- 清洁及干燥油底壳螺栓。
- 将工具 (B) 或工具 (C) 涂抹在螺栓螺纹上。
- 安装油底壳螺栓并将螺栓紧固至扭矩
55 ± 10 N·m (40 ± 7 lb ft) 。
Show/hide table图 4 g01022239 注: 漏油是经由发动机油底壳螺栓 (8) 的螺纹而产生的。 发动机右侧发动机缸体 (7) 前部的第三个螺栓为可疑螺栓。
- 从所有密封垫接头上擦去多余的工具 (A)。 使用平直工具来清除密封剂。
- 将工具 (C) 应用到管道螺塞 (3) 上。 安装管道螺塞 (3) 。 拧紧螺塞至扭矩为
80 ± 11 N·m (60 ± 8 lb ft) 。 - 安装排放塞 (4) 和 O 形密封圈。 拧紧螺塞至扭矩为
70 ± 15 N·m (50 ± 11 lb ft) 。Show/hide table图 5 g00516290 典型示例 - 将降噪盖 (1)定位在发动机油底壳上并安装六个螺栓 (2) 及垫圈。
- 向发动机加注机油到正确的油位。 请参阅操作和保养手册,了解正确的加注步骤。
Caterpillar Information System:
3406E Truck Engine Vibration Damper
G3300 Engines Ignition System Timing - Check/Adjust
3406E On-Highway Engine Inlet and Exhaust Valve Seals - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3612 and 3616 Engines Compression Release Valve
3116 and 3126 Marine Engines Reference Material
G3300 Engines Engine Crankcase Breather - Clean
3116 and 3126 Marine Engines Refill Capacities
3612 and 3616 Engines Manual Valve Group (Cylinder Pressure)
3406E On-Highway Engine Engine Oil Pan - Remove and Install
3406E On-Highway Engine Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
G3300 Engines Valve Data Sheet
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Remove
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Engine Oil Pump - Install
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
3406C (PEEC III) Truck Engines General Information
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Disassemble