Vibration Damper
Rubber Damper
Show/hide table
Illustration 1 | g00516262 |
Typical Example |
(1) Bolt
-
Apply 4C-5593 Anti-Seize Compound to all of the bolts at assembly.
- Tighten the bolts to the following torque. ... 215 ± 40 N·m (158 ± 29 lb ft)
(2) Adapter
(3) Damper assembly
Note: The dash marks on the front of the damper assembly must be in alignment with each other. A new damper assembly will be needed if the dash marks are not in alignment.
Visconic Damper
Show/hide table
NOTICE |
---|
Thoroughly inspect the viscous damper for signs of leakage or for signs of a dented (damaged) case. Either of these conditions can cause the weight to make contact with the case. This can affect the viscous damper's operation. |
Type 1
Show/hide table
Illustration 2 | g00379837 |
Typical example |
(1) Bolt
-
Apply 4C-5593 Anti-Seize Compound to all of the bolts at assembly.
- Tighten the bolts to the following torque. ... 215 ± 40 N·m (158 ± 29 lb ft)
(2) Adapter
(3) Damper assembly
(4) Pulley
Type 2
Show/hide table
Illustration 3 | g00914301 |
Typical Example |
(1) Adapter mounting bolt
- Tighten the bolts to the following torque. ... 215 ± 40 N·m (158 ± 29 lb ft)
(2) Damper assembly
(3) Mounting bolt
- Tighten the bolts to the following torque. ... 135 ± 20 N·m (100 ± 15 lb ft)
(4) Adapter
Caterpillar Information System:
G3300 Engines Ignition System Timing - Check/Adjust
3406E On-Highway Engine Inlet and Exhaust Valve Seals - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3612 and 3616 Engines Compression Release Valve
3116 and 3126 Marine Engines Reference Material
G3300 Engines Engine Crankcase Breather - Clean
3116 and 3126 Marine Engines Refill Capacities
3612 and 3616 Engines Manual Valve Group (Cylinder Pressure)
3406E On-Highway Engine Engine Oil Pan - Remove and Install
3406E On-Highway Engine Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3300 Engines Valve Data Sheet
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Remove
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Engine Oil Pump - Install
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules
3406C (PEEC III) Truck Engines General Information
3116 and 3126 Marine Engines Zinc Rods - Inspect/Replace