Inlet and Exhaust Valve Seals - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-7414     | 油封钩     | 1     |
B (1)     | 9U-6890     | 油封安装工具     | 1     |
C (1)     | 9U-7216     | 气门密封销     | 1     |
Show/hide table
( 1 ) | 9U-7226 密封安装工具 的部分工具 |
开始:
- 拆下进气门和排气门弹簧。 请参阅拆解和组装, "进气门和排气门弹簧 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 更换气门密封时,缸盖可以安装在发动机上,也可以从发动机上拆下。 无需将气门安装到缸盖即可安装气门密封。
Show/hide table
图 1 | g00516322 |
- 使用工具 (A) ,从气门 (1) 和气门导管 (3) 上拆下气门密封 (2) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-7414     | 油封钩     | 1     |
B (1)     | 9U-6890     | 油封安装工具     | 1     |
C (1)     | 9U-7216     | 气门密封销     | 1     |
Show/hide table
( 1 ) | 9U-7226 密封安装工具 的部分工具 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 2 | g00516322 |
Show/hide table
图 3 | g00516323 |
注: 按照步骤 1 和 2,将气门密封与气门一起安装到缸盖中。
- 在气门杆上涂抹薄薄一层清洁的发动机机油。 将气门密封 (2) 安置到气门 (1) 上。
- 使用工具 (B) 将气门密封 (2) 压到气门导管 (3) 上。
- 将气门密封 (2) 安置到工具 (B) 上。
注: 当已从缸盖上拆下气门时,按照步骤 3 至 7 安装气门密封。 使用工具 (C) (而不是气门杆)正确安置新的气门密封。
- 将工具 (C) 穿过工具 (B) 和新的气门密封。
- 将工具 (C) 放入气门导管孔。
- 使用工具 (B) 将气门密封 (2) 推到气门导管 (3) 上的适当位置。
- 从气门导管 (3) 上拆下工具 (B) 和工具 (C) 。
- 重复步骤 3 至 7,安装其余的气门密封。
End By: 安装进气门和排气门弹簧。 请参阅 拆解和组装, "进气门和排气门弹簧 - 拆卸和安装"。
Caterpillar Information System:
3176C and 3196 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3612 and 3616 Engines Compression Release Valve
3116 and 3126 Marine Engines Reference Material
G3300 Engines Engine Crankcase Breather - Clean
3116 and 3126 Marine Engines Refill Capacities
3612 and 3616 Engines Manual Valve Group (Cylinder Pressure)
3406E On-Highway Engine Engine Oil Pan - Remove and Install
3406E On-Highway Engine Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Remove
G3300 Engines Ignition System Timing - Check/Adjust
3406E Truck Engine Vibration Damper
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3300 Engines Valve Data Sheet
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Remove
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Engine Oil Pump - Install
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check
3524B Engines for Off-Highway Trucks ECM Will Not Communicate with Other Systems or Display Modules