Flywheel - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
B | FT2711 | 专用螺栓 | 2 |
C | FT2712 | 导向双头螺栓 | 2 |
- 用垫块或适当的起吊设备支撑好发动机。
Show/hide table
图 1 g01020856 - 将工具 (A) 安装到飞轮上。 将适当的起吊设备固定到飞轮上。
- 拆下一颗螺栓 (1) 和垫圈。 拆除与第一个螺栓成 180 度的另一个螺栓 (1)和垫圈。 用工具 (C)更换螺栓。
- 拆下其余的螺栓 ( 1) 和垫圈。
- 拆下飞轮 (3)。 将飞轮滑出双头导向螺栓。 飞轮的重量约为
57 kg (125 lb) 。注: 如果发动机配备一个后动力输出装置 RPTO ,则需要安装工具 ( B) 。 这一步骤可以将齿轮紧紧抵在曲轴端部。
- 检查飞轮齿圈 (2)。 如有必要,更换齿圈。 将飞轮放到木块上。 使用锤子和冲头来拆卸齿圈。
Caterpillar Information System:
G3300 Engines Before Starting Engine
3406C Engines for Caterpillar Built Machines Service Meter
3176C and 3196 Engines For Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Install
3406E On-Highway Engine Cylinder Head - Remove
3406C (PEEC III) Truck Engine Alternator
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Remove
3406E On-Highway Engine Turbocharger - Disassemble
3524B Engines for Off-Highway Trucks Engine Cranks but Will Not Start
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
G3300 Engines Starting the Engine
3406E On-Highway Engine Cylinder Head - Install
3176C and 3196 Industrial Engines Flywheel - Install
3612 and 3616 Engines Fuel Injector - Heavy Fuel Oil
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
C-18 Truck Engines Compression Brake - Inspect/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
3116 and 3126 Marine Engines Engine Oil Level Gauge - Calibrate