Speed Sensor (Engine) - Adjust
Show/hide table
Illustration 1 | g00289497 |
994 Engine Output Speed Sensor (1) Speed sensor. (2) Locknut. (A) Air gap. |
- Remove speed sensor (1). Align a gear tooth directly in the center of the threaded sensor opening.
- By hand, screw the speed sensor (1) into the hole until the end of the sensor contacts the gear tooth.
- Set the air gap of the speed sensor to
0.89 mm (0.035 inch) . The air gap is set by turning the sensor 180 degrees in the counterclockwise direction. - Tighten locknut (2) to
20 ± 5 N·m (15 ± 4 lb ft) .
Note: Do not allow speed sensor (1) to turn as locknut (2) is tightened.
Caterpillar Information System:
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Pilot Accumulator - Remove and Install
583R Pipelayer Power Train Transmission Mounting
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Position Sensor (Lift Arm) - Adjust
527 Track-Type Skidder Power Train Transmission Controls and Parking Brake Linkage
527 Track-Type Skidder Power Train Transmission
3176C and 3196 Engines for Caterpillar Built Machines Fuel System
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Disassemble
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Remove
3406E and 3456 Engines for Caterpillar Built Machines Fuel Pressure Sensor
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder - Assemble
784C and 785C Off-Highway Trucks Machine Systems Electronic Control Module (Power Train) - Remove and Install
583R Pipelayer Power Train Steering Clutch and Brake Controls Linkage
527 Track-Type Skidder Product Identification Number, Serial Number and EU's CE Plate Locations
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Module - Replace
3176C and 3196 Engines for Caterpillar Built Machines Engine Design
773D Off-Highway Truck and 775D Quarry Truck Transmission Planetary
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Battery - Replace
527 Track-Type Skidder Battery Disconnect Switch
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Master Cylinder - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Cable Connections
527 Track-Type Skidder Ether Starting Aid - If Equipped
3126 Truck Engine Engine Oil Temperature Sensor
527 Track-Type Skidder Electronic Monitoring System (EMS)