Metering Pump (Steering) - Assemble
Assembly Procedure
- Check the condition of all O-ring seals. If any seal is worn, use a new part for replacement.
Note: Make sure that all parts of the steering metering pump are clean prior to assembly. During assembly, apply clean SAE 10W oil on the internal parts of the steering metering pump.
- Install O-ring seals (3) and (5) on seat (4). Install retainer (1), ball (2), seat (4) and plug (6) in the pump body. The torque for plug (6) is 11.3 N·m (100 lb in).
Note: Make sure that the plug is flush with the surface of the pump body.
Show/hide table
Illustration 1 | g00508871 |
- Install seals (7) and (8) in the bushing.
Show/hide table
Illustration 2 | g00508872 |
- Install O-ring seal (9) in the housing. Install bushing (11) and spiral lockring (10) .
Show/hide table
Illustration 3 | g00508875 |
- Install the three springs in spool (12). Make sure that the curves of the springs are in contact and in the center of the spool. The notched side of the spring ends must face toward the sleeve.
Show/hide table
Illustration 4 | g00508876 |
- Install sleeve (13) over spool (12). The notch in the sleeve must engage with the ends of the springs.
- Install pin (14) .
Show/hide table
Illustration 5 | g00508879 |
- Put race (15), bearing (16) and race (17) in position on sleeve (13) .
Show/hide table
Illustration 6 | g00508878 |
- Install the O-ring seal in the housing. Put plate (19) in position and make an alignment of the bolt holes. Some of the holes are oil passages.
Show/hide table
Illustration 7 | g00508880 |
- Put drive (18) in position. Make sure that the notch in drive (18) engages with pin (14) in the sleeve assembly.
- Install rotor (21) and spacer (20). Make sure that rotor (11) is aligned with pin (14) in the sleeve assembly, as shown.
Show/hide table
Illustration 8 | g00508881 |
Show/hide table
Illustration 9 | g00279603 |
- Put O-ring seal (23) in position on barrel (22). Install barrel (22) onto the housing.
Show/hide table
Illustration 10 | g00508882 |
- Align the bolt holes.
- Put O-ring seal (25) in position on plate (24). Install plate (24) on the barrel. Align the bolt holes.
Show/hide table
Illustration 11 | g00508884 |
- Install seven bolts (26). Tighten the bolts in the following manner:
- Tighten the bolts in the numerical sequence. (See Illustration 13.) The initial torque for the bolts is 14.1 ± 2.8 N·m (125 ± 25 lb in).
Show/hide tableIllustration 13 g00279604
- Tighten the bolts again in the numerical sequence. (See Illustration 13.) The final torque for the bolts is 28.2 ± 2.8 N·m (250 ± 25 lb in).
Show/hide table
Illustration 12 | g00508885 |
End By: Install the metering pump. Refer to Disassembly and Assembly, "Metering Pump (Steering) - Install".
Caterpillar Information System:
3406E On-Highway Engine Camshaft - Remove
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Service Brake) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Secondary Brake) - Remove and Install
527 Track-Type Skidder Fire Prevention and Explosion Prevention
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Manual Retarder) - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Hydraulic Control Valve - Disassemble
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Automatic Retarder) - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Sensor Dynamic Test
773D Off-Highway Truck and 775D Quarry Truck Pressure Control Valve (Transmission)
D250E Series II and D300E Series II Articulated Trucks Power Train Torque Converter and Retarder - Connect
527 Track-Type Skidder Power Train Torque Converter
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Service and Parking Brake (Rear) - Disassemble
784C and 785C Off-Highway Trucks Machine Systems Air Control Valve (Parking Brake) - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Hydraulic Control Valve - Assemble
980G Wheel Loader Machine Systems Piston Pump (Steering) - Assemble
784C, 785C and 785C HAA Off-Highway Truck/Tractors Steering System Steering Tank and Filter
583R Pipelayer Power Train Transmission Selector and Pressure Control Valve
527 Track-Type Skidder Power Train Transmission Selector and Pressure Control Valve
583R Pipelayer Power Train Transmission Hydraulic Control
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air System
784C and 785C Off-Highway Trucks Machine Systems Pressure Protection Valve (Service Brake) - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Lift or Tilt Cylinder Sensor - Troubleshoot
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Accumulator Manifold - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Steering System Check