5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Caterpillar


CID 0262 FMI 04 Sensor Power Supply (5 DCV) Voltage Below Normal - Test

Usage:

793B 1HL
This diagnostic code is recorded when the ECM reads the voltage of the +5 DCV sensor supply circuit and the voltage is below normal. The circuit may be shorted to ground.

  1. CHECK THE VOLTAGE AT THE INTERFACE MODULE.

    1. Turn the disconnect switch and the key start switch to the ON position.

    2. Check the voltage at the connector of the interface module from contact 27 (sensor supply) to contact 2 (ground). Use the 7X-1710 Cable probes to measure the voltage. Do NOT disconnect the machine harness from the VIMS main module.

      Expected Results: Voltage is 5.0 ± 0.5 DCV.

      Results:

      • OK - Voltage is 5.0 ± 0.5 DCV. The sensor supply voltage is correct. Check the message center in order to verify that the same diagnostic code is present. If the diagnostic code is still present the interface module has failed. Replace the module. Refer to the Testing and Adjusting, "Module - Replace" section. STOP.

      • NOT OK - Voltage is NOT 5.0 ± 0.5 DCV. The voltage is less than 5.0 ± 0.5 DCV. The sensor supply voltage is NOT correct. proceed to 2.

  2. CHECK FOR SHORT TO GROUND

    1. Turn the key start switch and the disconnect switch to the OFF position.

    2. Disconnect the machine harness from the VIMS interface module.

    3. At the VIMS interface module harness connector , measure the resistance between frame ground and the contact 27 of the sensor supply circuit.

      Expected Results: Resistance is greater than 5000 ohms.

      Results:

      • OK - Resistance is greater than 5000 ohms. The harness circuit resistance is correct. The VIMS interface module has failed. Replace the VIMS interface module. Refer to the Testing and Adjusting, "Module - Replace" section. STOP.

      • NOT OK - Resistance is less than 5000 ohms. The machine harness or a sensor has failed. Proceed to 3.

  3. DISCONNECT THE SENSORS.

    1. The key start switch and the disconnect switch remain in the OFF position.

    2. One at a time disconnect any sensor that uses the +5 DCV interface module sensor supply from the machine harness, that is associated with this diagnostic code.

    3. After disconnecting the sensor (s), check the resistance from frame ground to contact 27 (sensor supply) of the machine harness connector for the VIMS interface module.

      Expected Results: Resistance is greater than 5000 ohms.

      Results:

      • OK - Resistance is greater than 5000 ohms. The harness circuit resistance is correct. The sensor that was just disconnected has failed. Replace the sensor. STOP.

      • NOT OK - Resistance is less than 5000 ohms. If the resistance is less than 5000 ohms after all the sensors have been disconnected from the machine harness. The machine harness is shorted to ground. Repair the machine harness or replace the machine harness. STOP.

Caterpillar Information System:

5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0262 FMI 03 Sensor Power Supply (5 DCV) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 06 Sensor Power Supply (8 DCV) Current Above Normal - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Differential
3176C and 3196 Engines for Caterpillar Built Machines Fuel Priming Pump
3406C Engines for Caterpillar Built Machines Engine Support (Rear)
583R Pipelayer Power Train Final Drive, Steering Clutch, and Brakes - Connect
583R Pipelayer Power Train Final Drive, Steering Clutch, and Brakes - Separate
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Wiring
793C and 793C XQ Off-Highway Truck Air System and Brakes Inverter Valve (Secondary Brake)
3406C Engines for Caterpillar Built Machines Engine Support (Front)
G3B, K3A and L3A Denso Alternators T5 Alternator Current - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 04 Sensor Power Supply (8 DCV) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0262 FMI 06 Sensor Power Supply (5 DCV) Current Above Normal - Test
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Slack Adjuster (Rear) - Remove
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0248 FMI 09 Cat Data Link Abnormal Update - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0263 FMI 03 Sensor Power Supply (8 or 12 DCV) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0263 FMI 04 Sensor Power Supply (8 or 12 DCV) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0263 FMI 06 Sensor Power Supply (8 or 12 DCV) Current Above Normal - Test
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Slack Adjuster (Rear) - Install
980G Wheel Loader Power Train Output Transfer Gears from Transmission, Torque Converter - Separate
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0271 FMI 05 Alarm (Action) Current Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0271 FMI 06 Alarm (Action) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0324 FMI 03 Lamp (Action) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0324 FMI 05 Lamp (Action) Current Below Normal - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.