5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Caterpillar


CID 0428 FMI 04 Temperature Sensor (Rear Axle Oil) Voltage Below Normal - Test

Usage:

793B 1HL


Illustration 1g00502794
Schematic of the Rear Axle Oil Temperature Sensor

This diagnostic code is recorded when VIMS reads the voltage of the rear axle oil temperature sensor as being below normal. The voltage of the signal wire is below normal and/or shorted to ground. The sensor sends a PWM signal to the VIMS module.

The possible causes of this diagnostic code are listed here:

  • The sensor has failed.

  • The signal circuit in the machine harness is shorted to ground.

  • The VIMS interface module has failed. This is unlikely.

  1. CHECK THE SENSOR.

    1. Turn the disconnect switch and the key start switch to the ON position.

    2. Observe the status of the diagnostic code. Then disconnect the machine harness from the sensor.

      Expected Result: If the sensor is not the cause of the diagnostic code, the diagnostic code remains active. If the sensor has failed, the diagnostic code is NO longer active.

      Note: VIMS may wait up to approximately 30 seconds before updating the message area.

      Results:

      • OK - This diagnostic code remains active. The sensor is not causing the diagnostic code. The machine harness or the ECM may have failed. Proceed to 2.

      • NOT OK - This diagnostic code is NO longer active. The machine harness is correct and the ECM is operating properly. The sensor has failed. Replace the sensor. Refer to the Testing and Adjusting, "Pulse Width Modulated (PWM) Sensor -Test" section. STOP.

  2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND.

    1. The sensor remains disconnected from the machine harness.

    2. Turn the key start switch and the disconnect switch to the OFF position.

    3. Disconnect the machine harness from the VIMS interface module.

    4. At the machine harness connector for the VIMS interface module, measure the resistance between the signal contact and frame ground.

      Expected Result: The resistance is greater than 5000 ohms.

      Results:

      • OK - Resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to 3

      • NOT OK - Resistance is less than 5000 ohms. The machine harness has failed. There is a short between frame ground and the signal circuit in the machine harness. Repair the machine harness or replace the machine harness. STOP.

  3. CHECK IF THE DIAGNOSTIC CODE REMAINS.

    1. Using established procedures, clean the contacts of the harness connectors.

    2. Reconnect all harness connectors.

    3. Turn the disconnect switch and the key start switch to the ON position.

    4. Observe the status of the diagnostic code.

    5. Operate the machine.

    6. Observe the status of the diagnostic code.

      Expected Result: The diagnostic code CID 0427 FMI 04 is no longer active.

      Results:

      • YES - Diagnostic code is NOT active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and then reconnected. Resume normal machine operation. STOP.

      • NO - Diagnostic code has not been corrected. It is unlikely that the ECM is faulty. Exit this CID/FMI procedure and perform this CID/FMI procedure again. If the cause of the fault is not found, then replace the VIMS interface module. See Testing And Adjusting, " Module - Replace". STOP.

Caterpillar Information System:

769D Off-Highway Truck and 771D Quarry Truck Oil Filter (Parking Brake Release) - Replace
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0428 FMI 03 Temperature Sensor (Rear Axle Oil) Voltage Above Normal - Test
769D Off-Highway Truck and 771D Quarry Truck Breather (Air/Hydraulic Cylinder) - Replace
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0427 FMI 06 Temperature Sensor (Front Axle Oil) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0427 FMI 04 Temperature Sensor (Front Axle Oil) Voltage Below Normal - Test
980G Wheel Loader Power Train Transmission Hydraulic Control Valve - Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0426 FMI 06 Pressure Sensor (Rear Brake Oil) Current Above Normal - Test
793C Off-Highway Truck Machine Systems Transmission Control (Select Lever) - Remove and Install
769D Off-Highway Truck and 771D Quarry Truck Screen (Hoist and Brake Tank) - Inspect/Clean/Replace
988G Wheel Loader Ether Starting Aid
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0426 FMI 04 Pressure Sensor (Rear Brake Oil) Voltage Below Normal - Test
769D Off-Highway Truck and 771D Quarry Truck Hoist and Brake Tank Oil Level - Check
3054 Engine Exhaust Manifold
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0428 FMI 06 Temperature Sensor (Rear Axle Oil) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0429 FMI 03 Pressure Sensor (Steering Oil) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0429 FMI 04 Pressure Sensor (Steering Oil) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0429 FMI 06 Pressure Sensor (Steering Oil) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0430 FMI 03 Pressure Sensor (Steering Pilot Oil) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0430 FMI 04 Pressure Sensor (Steering Pilot Oil) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0430 FMI 06 Pressure Sensor (Steering Pilot Oil) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0434 FMI 03 Pressure Sensor (Hydraulic Pilot Oil) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0434 FMI 04 Pressure Sensor (Hydraulic Pilot Oil) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0434 FMI 06 Pressure Sensor (Hydraulic Pilot Oil) Current Above Normal - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Brake and Planetary - Disassemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.