5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Caterpillar


CID 0379 FMI 03 Pressure Sensor (Automatic Lubrication) Voltage Above Normal - Test

Usage:

793B 1HL


Illustration 1g00730057
Schematic of the Pressure Sensor (Auto Lube)

This diagnostic code is recorded when the VIMS reads the voltage of the pressure sensor (auto lube) and the voltage is above normal. The sensor sends a PWM signal to the VIMS module.

The possible causes of this diagnostic code are listed here:

  • A shorted harness

  • An open supply circuit to the sensor

  • A failed sensor

  • An open circuit

  • The VIMS interface Module may have failed. This is unlikely.

Note: Ensure that the diagnostic code is still active.

Note: The following procedure can create numerous related diagnostic codes. Reconnect all harnesses. Then, the related diagnostic codes will be shown as being NOT active. Complete the following procedure. Then, clear all of the related diagnostic codes.

  1. CHECK THE SUPPLY VOLTAGE AT THE SENSOR.

    1. Turn the disconnect switch and the key start switch to the ON position.

    2. Check the voltage at the machine harness connector of the sensor from contact A (sensor supply) to contact B (ground). Do NOT disconnect the sensor. Use the 7X-1710 Cable probes to measure the voltage.

      Expected Results: The voltage should measure approximately 8 DCV.

      Results:

      • OK - The voltage is approximately 8 DCV. The voltage is correct. Proceed to 3.

      • NOT OK - The voltage is not approximately 8 DCV. There is an open in the machine harness or the ECM has failed. It is unlikely that the ECM has failed. Proceed to 2.

  2. CHECK FOR AN OPEN IN THE SUPPLY CIRCUIT.

    1. The key start switch and the disconnect switch remain in the ON position.

    2. Disconnect the sensor from the machine harness.

    3. At the machine harness connector for the sensor, measure the voltage from contact A (sensor supply) to frame ground.

      Expected Results: The voltage should measure approximately 8 DCV.

      Results:

      • OK - The voltage measures approximately 8 DCV. The return circuit is open. Repair the machine harness or replace the machine harness. STOP.

      • NOT OK - The voltage does not measure approximately 8 DCV. The supply circuit is open. Repair the machine harness or replace the machine harness. STOP.

  3. CHECK THE SIGNAL CIRCUIT.

    1. Turn the disconnect switch and the key start switch to the ON position.

    2. Disconnect the machine harness connector from the sensor.

    3. At the machine harness connector for the sensor, measure the voltage between contact C (signal) and contact B (ground).

      Expected Results: The voltage should measure approximately 5 DCV.

      • OK - The voltage is approximately 5 DCV. The voltage is correct. Replace the sensor. STOP

      • NOT OK - The voltage is NOT approximately 5 DCV. The voltage is NOT correct. Proceed to 4.

  4. CHECK FOR AN OPEN SIGNAL CIRCUIT.

    1. Turn the key start switch and the disconnect switch to the OFF position.

    2. The sensor remains disconnected from the machine harness.

    3. Disconnect the machine harness from the interface module.

    4. Place a jumper wire between contact C (signal) and contact B (ground) of the machine harness connector for the sensor.

    5. At the machine harness connector of the interface module, measure the resistance between the signal contact and frame ground.

      Expected Result: The resistance measures less than 10 ohms.

      Results:

      • OK - The resistance measures less than 10 ohms. The circuit is correct. Proceed to 5.

      • NOT OK - The resistance is greater than 5000 ohm. The circuit is open. Repair the machine harness or replace the machine harness. STOP.

  5. CHECK THE SIGNAL WIRE FOR SHORTS.

    1. The disconnect switch and the key start switch remain in the OFF position.

    2. The machine harness remains disconnected from the VIMS interface module.

    3. Remove the jumper wire from contact C and contact B on the machine harness connector for the sensor.

    4. At the machine harness connector for the VIMS interface module measure from the signal contact to all possible sources of +Battery.

      Expected Results: Each measurement is greater than 5000 ohms.

      • OK - Each measurement is greater than 5000 ohms. The ECM has failed. Refer to the Testing and Adjusting, "Module - Replace" section. STOP.

      • NOT OK - The resistance measured less than 5000 ohms. There is a short in the machine harness. Repair the machine harness or replace the machine harness. STOP.

Caterpillar Information System:

836G Landfill Compactor and 834G Wheel Dozer Differential Thrust Pin Clearance - Check
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0280 FMI 03 Temperature Sensor (Pump Drive) Voltage Above Normal - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Piston Pump (Hydrostatic)
CB-534C Vibratory Compactor Drum Scrapers - Inspect/Adjust/Replace
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0279 FMI 03 Temperature Sensor (Front Aftercooler Coolant) Voltage Above Normal - Test
836G Landfill Compactor and 834G Wheel Dozer Crankshaft Vibration Damper - Inspect
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0177 FMI 06 Temperature Sensor (Transmission Oil) Current Above Normal - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train General Information
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0177 FMI 04 Temperature Sensor (Transmission Oil) Voltage Below Normal - Test
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Breaker Relief Valve (Hydraulic Tank)
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Solenoid Valve (Swing Brake)
784C and 785C Off-Highway Trucks Machine Systems Tire and Rim (Front) - Remove and Install
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Solenoid Valve (Signal Cutoff)
836G Landfill Compactor and 834G Wheel Dozer Light Switches
3306C Engines for Caterpillar Built Machines Flywheel Housing
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0425 FMI 03 Pressure Sensor (Front Brake Oil) Voltage Above Normal - Test
143H and 163H Motor Graders All Wheel Drive Service Record
980G Wheel Loader Power Train Transmission Hydraulic Control Valve - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0426 FMI 03 Pressure Sensor (Rear Brake Oil) Voltage Above Normal - Test
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Pressure Reducing Valve (Color Marking System)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0427 FMI 03 Temperature Sensor (Front Axle Oil) Voltage Above Normal - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydraulic Oil Filter
769D Off-Highway Truck and 771D Quarry Truck Engine Oil Level - Check
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.