IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Caterpillar


Fixed Axle (Front) - Install

Usage:

IT14G 1WN

Installation Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8S-8048     Saddle     2    
8S-7615 Pin     2    
8S-7641 Tube     2    
8S-7630 Stand     2    
B     1U-9760     Jack Stand Gp     2    

------ WARNING! ------

Personal injury can result working with the tire and rim without precautions.

Personal injury can result if the weight shifts and causes movement of the tire and rim.

When starting nuts on the studs, do not put your arm between the rim and final drive without first wedging a block of oak between the rim and final drive.

----------------------


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.

Dispose of all fluids according to local regulations and mandates.


Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.




    Illustration 1g00494545

  1. Use suitable lifting devices (4) on each side of the front axle.

  1. Raise the front axle to the machine and install the front axle to the machine.

  1. Install eight washers and bolts (5) to the front axle. Tighten the bolts to a torque of 300 ± 40 N·m (220 ± 30 lb ft).



    Illustration 2g00494542

  1. Connect tube assembly (3) to the front axle.



    Illustration 3g00494540

  1. Install front fender (2) on each side of the machine and three bolts (1) .

End By:

  1. Install the drive shaft. Refer to Disassembly and Assembly, "Drive shaft - Remove and Install".
  2. Install the tire and rim. Refer to Disassembly and Assembly, "Tire and Rim - Remove and Install".
  3. Disconnect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".

Caterpillar Information System:

Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Midroller
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Pilot System Pressure - Test
950G Wheel Loader and 962G Wheel Loader Electrohydraulic System Implement Cycle Time - Check
966F Wheel Loader and 966F Series II Wheel Loader Hydraulic System Lift and Tilt Cylinder Drift - Check
793C and 793C XQ Off-Highway Truck Air System and Brakes Air Tank
789C Off-Highway Truck/Tractor Air System and Brakes Air Dryer
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Lift Cylinder - Isolation and Drift Check
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H and 16H Motor Graders Caterpillar Monitoring System Scrolling Mode
AP-1050B and BG-245C Asphalt Pavers Conveyor Systems Position Sensor (Paddle)
583R Pipelayer Engine Supplement Radiator Guard and Radiator - Tilt
793C Off-Highway Truck Machine Systems Gear Pump (Hoist) - Assemble
793B Off-Highway Truck Air System and Brakes Air Compressor
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Color Marking System - If Equipped
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Resolver Network Check
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Bank Valve - Assemble
583R Pipelayer Power Train Torque Converter Outlet Relief Valve - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Belt Tensioner
583R Pipelayer Power Train Torque Converter Outlet Relief Valve - Disassemble
3412E and C30 Engines Engine Design
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Differential Steer Unit
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Power Train Front Idler
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Ride Control Accumulator - Test and Charge
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Relief Valve (Hoist Dual Stage)
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Prelubrication Function
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.