Track Roller - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | A     |
1P-1861 Retaining Ring Pliers     | 1     |
Start By:
- Remove the track rollers. Refer to Disassembly and Assembly, "Track Roller - Remove" for the machine that is being serviced.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove the plug from stopper (2) by using a hammer and a punch.
Show/hide table
Illustration 1 | g00556924 |
- Use a variable speed drill and a 12.7 mm (0.500 inch) drill bit in order to remove stopper (2) from the shaft.
Show/hide table
NOTICE |
---|
Removal of the plug and stopper (2) will damage the stopper (2) . |
- Remove lock ring (3) and end collar (1) from both sides of the track roller.
- Remove Duo-Cone seal kit (4) from end collar (1) .
Show/hide table
Illustration 2 | g00556926 |
Note: Mark the Duo-Cone seal kits for the proper installation.
- Use Tooling (A) and remove retaining ring (5) from rim assembly (6) .
Show/hide table
Illustration 3 | g00556930 |
- Repeat Step 5 for the opposite side.
- Use a press and roller shaft (7) in order to remove the bushing assembly on the opposite side of the rim assembly.
Show/hide table
Illustration 4 | g00556932 |
- Flip the roller assembly. Use the press and roller shaft (7) in order to remove the remaining bushing assembly.
Show/hide table
Illustration 5 | g00556933 |
- Remove O-ring seals (8) from roller shaft (7) .
Show/hide table
Illustration 6 | g00556935 |
- Remove O-ring seal (9) from bushing assembly (10) .
Show/hide table
Illustration 7 | g00556936 |
- Remove Duo-Cone seal kit (11) from bushing assembly (10) .
Caterpillar Information System:
D5M Track-Type TractorPower Train Track Roller - Assemble
D5M Track-Type TractorPower Train Track Carrier Roller - Remove
D5M Track-Type TractorPower Train Track Carrier Roller - Install
D5M Track-Type TractorPower Train Track Carrier Roller - Disassemble
D5M Track-Type TractorPower Train Track Carrier Roller - Assemble
D5M Track-Type TractorPower Train Track Adjuster - Remove and Install
D5M Track-Type TractorPower Train Track - Separate
D5M Track-Type TractorPower Train Track - Disassemble
D5M Track-Type TractorPower Train Track - Connect
D5M Track-Type TractorPower Train Track - Assemble
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Remove
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Install
D5M Track-Type TractorPower Train Track Roller - Install
D5M Track-Type TractorPower Train Track Roller - Remove
D5M Track-Type TractorPower Train Track Roller Frame - Install
D5M Track-Type TractorPower Train Track Roller Frame - Remove
D5M Track-Type TractorPower Train Transmission - Assemble
D5M Track-Type TractorPower Train Transmission - Disassemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Assemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Disassemble
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Install
D5M Track-Type TractorPower Train Transmission Hydraulic Control Valve - Remove
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Connect
D5M Track-Type TractorPower Train Transmission and Bevel Gears - Install