D5M Track-Type TractorPower Train Caterpillar


Track - Separate

Usage:

D5M 3CR

Separation Procedure

Table 1
Required Tools     A     B    
8S-7610 Base     2        
8S-7650 Cylinder     2        
9U-6600 Hand Hydraulic Pump     2        
8S-7640 Stand         2    
8S-7611 Tube         2    
8S-7615 Pin         2    



    Illustration 1g00556976

  1. Remove the bolts and cover (1) from the roller frame. Remove the O-ring seal from the cover.



    Illustration 2g00556978

    ------ WARNING! ------

    Personal injury can result from grease under high pressure.

    The adjuster cylinder for the track is under high hydraulic pressure. Grease under high pressure can cause injury.

    Do not visually inspect the adjuster to see if grease is released when the valve is opened. Check the rod to see that it moves to the rear into the front support on the track roller frame.

    ----------------------

  1. Loosen the track by using the following procedure:

    1. Rotate relief valve (2) in a counterclockwise direction for one turn in order to allow grease to be released from the track adjuster. If the track does not loosen, go to Step 2.b.

    1. Rotate fill valve (3) in a counterclockwise direction for one turn in order to allow grease to be released from the track adjuster. If the track does not loosen, start the machine. Move the machine forward and backward. If the track is not released, go to Step 2.c.

    1. Install a piece of round bar stock between the bushing and the sprocket inside the links. Move the machine to the rear so the track will be pushed upward by the round bar stock. This will put tension on the track and this will move the track adjuster inward.



    Illustration 3g00556979

  1. Move the track until the master link is in alignment with the centerline of rear idler (5). Put wood blocks under the individual grouser bar. Position the blocks just below the master link.

  1. Remove four bolts (6) and master shoe (4) .

    ------ WARNING! ------

    Keep away from the front of the machine when the track is pushed off the final drive. A minimum distance of 7.6 m (25 ft) is needed in front of the track to permit the track to move out onto the floor.

    ----------------------



    Illustration 4g00684894

  1. Fasten a chain to the end of track (7) and to a wheel loader. Turn the final drive in a forward direction and allow track (7) to fall forward while the wheel loader is moved forward.

  1. If necessary, remove the track by using Tooling (A) in order to lift the side of the machine. Put Tooling (B) into position under the machine on Tooling (B) .

  1. Remove the track from the track roller frame. The weight of the track is approximately 680 kg (1500.0 lb).

Caterpillar Information System:

D5M Track-Type TractorPower Train Track - Disassemble
D5M Track-Type TractorPower Train Track - Connect
D5M Track-Type TractorPower Train Track - Assemble
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Remove
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Install
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Disassemble
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Assemble
D5M Track-Type TractorPower Train Torque Converter - Remove
D5M Track-Type TractorPower Train Torque Converter - Install
515 Wheel Skidder and 525 Wheel Skidder Drive Shaft Spline (Front) - Lubricate
D5M Track-Type TractorPower Train Torque Converter - Disassemble
3306C Engines for Caterpillar Built Machines Governor
D5M Track-Type TractorPower Train Track Adjuster - Remove and Install
D5M Track-Type TractorPower Train Track Carrier Roller - Assemble
D5M Track-Type TractorPower Train Track Carrier Roller - Disassemble
D5M Track-Type TractorPower Train Track Carrier Roller - Install
D5M Track-Type TractorPower Train Track Carrier Roller - Remove
D5M Track-Type TractorPower Train Track Roller - Assemble
D5M Track-Type TractorPower Train Track Roller - Disassemble
D5M Track-Type TractorPower Train Track Roller - Install
D5M Track-Type TractorPower Train Track Roller - Remove
D5M Track-Type TractorPower Train Track Roller Frame - Install
D5M Track-Type TractorPower Train Track Roller Frame - Remove
D5M Track-Type TractorPower Train Transmission - Assemble
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.