3406E On-Highway Engine Caterpillar


Electronic Unit Injector Sleeve - Install

Usage:

3406E 1MM

安装步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
B     9U-6862     锥形碳刷     1    
9U-6863 小号孔刷     1    
9U-7244 底刷     1    
9U-7237 刷子扩展工具     1    
4C-5552 大号膛刷     1    
(1)     221-9778     拉拔器螺柱     1    
(1)     9U-7258     驱动装置盖     1    
E     4C-9507     挡圈固定胶     -    
( 1 ) 9U-6891 喷油器工具总成 的部分工具


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。


  1. 使用工具 (B) 清洁缸盖中单体喷油器套管的孔。


    注意

    开始安装之前,请确保单体喷油器套管及单体喷油器套管的缸盖孔完全没有油、 污垢和密封剂碎屑。





    图 1g01003258

  1. 将新的 O 形密封圈 (2) 安装到单体喷油器套管 (1) 上。

    注: 请勿将工具 (E) 涂抹到缸盖表面。 仅在单体喷油器套管上涂抹工具 (E) 。

  1. 将工具 (E) 涂抹在接触面上标有 (X) 的位置。

  1. 用清洁的发动机机油润滑 O 形密封圈 (2) 。

  1. 将工具 (C) 拧入单体喷油器套管 (1) 的螺纹。

  1. 将工具 (C) 和单体喷油器套管 (1) 放入缸盖中。 小心不要损坏单体喷油器套管上的 O 形密封圈。


    注意

    确保单体喷油器套管正确放入缸盖中。 当单体喷油器套管完全放入缸盖的孔中时,工具和单体喷油器套管将变成"环状"。





    图 2g01027804

  1. 使用工具 (D) 和锤子安装单体喷油器套管。

  1. 使用清洁的毛巾擦除任何多余的固定剂。

  1. 向冷却系统加注冷却液。 请参阅操作和保养, "加注容量"以了解冷却系统容量。

End By: 安装电子单体喷油器。 请参阅 拆解和组装电子单体喷油器, "- 安装"。

Caterpillar Information System:

3306C Engines for Caterpillar Built Machines Engine Design
3600 Heavy Fuel Engines Exhaust Manifold - Inspect
3612 and 3616 Fast Vessel Engines Alarms and Shutoffs
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 444 FMI 12 Starting Motor Relay Failed - Test
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
G3612 and G3616 Engines Air Inlet and Exhaust System
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 443 FMI 12 Crank Termination Relay Failed - Test
3406E On-Highway Engine Fuel Transfer Pump - Remove
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 441 FMI 12 Electronic Governor Relay Failed - Test
3306C Truck Engine Crankshaft Front Seal - Remove
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 442 FMI 12 Generator Fault Relay Failed - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 445 FMI 12 Run Relay Failed - Test
3406E On-Highway Engine Electronic Unit Injector Sleeve - Remove
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 446 FMI 12 Air Shutoff Relay Failed - Test
3306B Industrial Engine Fuel Injection Pump
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 447 FMI 12 Fuel Control Relay Failed - Test
G3612 and G3616 Engines Engine Timing Procedures
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 500 FMI 12 EMCP Electronic Control (Generator Set) Failed - Test
3406C Engines for Caterpillar Built Machines Camshaft
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
3406C Engines for Caterpillar Built Machines Cylinder Head Valves
3306B Industrial Engine Fuel Injection Pump Housing
C-10 and C-12 Truck Engines Crankshaft
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.