Crankshaft Front Seal - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
B | 5P-1733 | Seal Locator | 1 |
C | 5P-1737 | Bolt | 3 |
D | 9S-8858 | Nut (Seal Installer) | 1 |
E | 6V-6142 | Seal Installer | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the crankshaft front seal and the wear sleeve are separated, these components cannot be used again.
Note: Do not use any type of lubricant during the installation of the crankshaft front seal and the wear sleeve.
- Fasten Tooling (B) to the crankshaft with Tooling (C).
Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft rotation toward the front of the engine.
- Position wear sleeve (2) and crankshaft front seal (1) on Tooling (B). Install Tooling (E) on Tooling (B). Lubricate the face of the washer on Tooling (D). Install Tooling (D) on Tooling (B).
- Tighten Tooling (D) until Tooling (E) contacts Tooling (B).
- Remove Tooling (D), and Tooling (E) from Tooling (B).
- Remove Tooling (C) and Tooling (B) from the crankshaft.
Show/hide table
Illustration 1 | g01042507 |
End By:
- Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 110 FMI 2 Temperature Sensor (Engine Coolant) Incorrect Signal - Test
C-10 and C-12 Industrial Engines Engine Oil Pan
C-10 and C-12 Truck Engines Engine Oil Pan
Electronic Modular Control Panel II (EMCP II) for EUI Engines Typical Generator Abbreviations
Electronic Modular Control Panel II (EMCP II) For MUI Engines Relay Module - Replace
Electronic Modular Control Panel II (EMCP II) For MUI Engines EMCP Electronic Control (Generator Set) - Replace
Electronic Modular Control Panel II (EMCP II) For MUI Engines EMCP Electronic Control (AC Transformer Box) - Replace
3612 and 3616 Engines Gear Group (Rear)
C-10 and C-12 Truck Engines Basic Block
3306C Truck Engine Pistons and Connecting Rods - Install
3306C Truck Engine Pistons and Connecting Rods - Remove
3412E, C30 and C32 Marine Engines Connecting Rod Bearings - Install
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 168 FMI 3 Electrical System Voltage Above Normal - Test
G3612 and G3616 Engines Air Lines - Choke
G3612 and G3616 Engines Exhaust Bypass Valve
3126 Truck Engine (Military) S·O·S Oil Analysis
C-18 Truck Engines S·O·S Coolant Analysis
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 168 FMI 4 Electrical System Voltage Below Normal - Test
G3500B Engines Manifold Air Pressure Sensor
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
G3500B Engines Engine Oil Pressure Sensor
3306C Truck Engine Pistons and Connecting Rods - Disassemble
G3500B Engines Oxygen Sensor