Engine Oil Filter Base
Show/hide table
 | |
| 图 1 | g01436835 |
(1) 盖 (2) 机油滤清器座 (5) 机油滤清器 (6) O 形密封圈 (8) O 形密封圈 (9) 阀柱塞 (10) O 形密封圈 (12) 泵旁通阀 (13) O 形密封圈 (14) O 形密封圈 (15) 隔套 (17) O 形密封圈 (19) 阀柱塞 (20) O 形密封圈 | |
(3) 双头螺柱
-
装配前，将 155-0695 螺纹固定剂 涂抹在螺柱上。 机油粗滤器安装螺柱比锥形锁紧螺柱长。
- 将螺柱拧入机油滤清器底座至以下扭矩。 ... 68 ± 7 N·m (50 ± 5 lb ft)
(4) 安装螺栓
将 9S-3263 螺纹固定剂 涂抹在六个安装螺栓中的每一个上。
Show/hide table
 | |
| 图 2 | g01116558 |
剖面 A-A | |
(7) 4N-8150 弹簧
- 组装后的长度 ... 55.25 mm (2.175 in)
- 组装长度上的负载 ... 75 ± 6 N (17.0 ± 1.3 lb)
- 测试后的自由长度 ... 93.7 mm (3.69 in)
- 外径 ... 20.6 mm (0.81 in)
- 组装长度上的负载 ... 75 ± 6 N (17.0 ± 1.3 lb)
Show/hide table
 | |
| 图 3 | g01116562 |
剖面 B-B | |
(11) 2N-6005 弹簧
- 组装后的长度 ... 96.52 mm (3.800 in)
- 组装长度上的负载 ... 92.52 N (21 lb)
- 最小工作长度 ... 45.72 mm (1.800 in)
- 最小工作长度上的负载 ... 257.55 N (58 lb)
- 测试后的自由长度 ... 124.71 mm (4.910 in)
- 外径 ... 21.84 mm (0.860 in)
- 组装长度上的负载 ... 92.52 N (21 lb)
Show/hide table
 | |
| 图 4 | g01116568 |
C-C 部分 | |
释放压力 ... 696 kPa (101 psi)
(16) 1A-2170 压紧弹簧
- 组装后的长度 ... 21.4 mm (0.84")
- 组装长度上的负载 ... 200 ± 15.5 N (45 ± 3.5 lb)
- 测试后的自由长度 ... 31.0 mm (1.22 in)
- 外径 ... 19.6 mm (0.77 in)
- 组装长度上的负载 ... 200 ± 15.5 N (45 ± 3.5 lb)
Show/hide table
 | |
| 图 5 | g01116570 |
截面 D-D | |
(18) 4N-8150 弹簧
- 组装后的长度 ... 55.25 mm (2.175 in)
- 组装长度上的负载 ... 75 ± 6 N (17.0 ± 1.3 lb)
- 测试后的自由长度 ... 93.7 mm (3.69 in)
- 外径 ... 20.6 mm (0.81 in)
- 组装长度上的负载 ... 75 ± 6 N (17.0 ± 1.3 lb)
Caterpillar Information System:
3306C Truck Engine Crankshaft - Install
3306C Truck Engine Crankshaft - Remove
3176C and 3196 Industrial Engines Belt Tensioner
3306B Industrial Engine Piston Cooling Jets - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Bearing Clearance - Check
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Disassemble
3306C Truck Engine Water Pump - Install
3306C Truck Engine Water Pump - Remove
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil and Filter - Change
3306C Truck Engine Water Temperature Regulator - Remove and Install
3306C Truck Engine Exhaust Manifold - Remove and Install
G3612 and G3616 Engines Air Starting System
G3606 and G3608 Engines Lubrication System
Electronic Modular Control Panel II (EMCP II) for EUI Engines Component Location
Electronic Modular Control Panel II (EMCP II) for EUI Engines EMCP Electronic Control (Generator Set)
C-10 and C-12 Truck Engines Air Inlet and Exhaust System
3406E, C-10 and C-12 Truck Engines Electronic Unit Injector - Inspect/Adjust
3406E, C-10, C-12, C-15, C-16 Truck Engines Fuel System - Prime
3176C and 3196 Industrial Engines Cylinder Head
G3606 and G3608 Engines Basic Block
3306C Truck Engine Rear Power Take-Off (RPTO) - Remove and Install
3306C Truck Engine Front Housing - Remove
3306C Truck Engine Front Housing - Install