Water Pump - Disassemble
解体步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 8H-0663     | 轴承拉拔器     | 1     |
B     | 1P-0510     | 冲头总成     | 1     |
C     | 1P-1861     | 挡圈钳     | 1     |
开始:
- 拆卸水泵。 请参考解体与组装, "水泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆卸螺栓 (9) 和垫圈。 将轴承 (12) 和齿轮 (15) 作为一个整体拆下。
Show/hide table
图 1 | g00509206 |
- 使用工具 (A) 、工具 (B) 和压力机将轴承 (12) 从齿轮 (15) 上拆下。
- 使用工具 (C) 拆下卡环 (6) 。
- 将两根螺栓 (11) 、垫圈、盖 (1) 和密封垫 (2) 从水泵壳 (14) 上拆下。
- 拧松螺栓 (9) 约 6.4 mm (.25 in)。 用软锤敲击螺栓,松开叶轮 (13) 。
- 拆下螺栓 (9) 、垫圈 (10) 和叶轮 (13) 。
- 将轴承 (5) 和轴 (8) 作为一个整体拆下。
- 使用工具 (A) 、工具 (B) 和压力机拆下轴承 (5) 。
- 拆下水泵密封组件 (3) 。
- 使用工具 (B) 拆下唇式密封件 (4) 。
Caterpillar Information System:
3306C Truck Engine Water Pump - Install
3306C Truck Engine Water Pump - Remove
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil and Filter - Change
3306C Truck Engine Water Temperature Regulator - Remove and Install
3306C Truck Engine Exhaust Manifold - Remove and Install
3406E, C-10 and C-12 Truck Engines Belt Tensioner - Inspect
G3612 and G3616 Engines Engine Design
3306C Truck Engine Turbocharger Wastegate - Remove and Install
G3612 and G3616 Engines Engine Design
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level Gauge - Calibrate - C-10 and C-12 Engines Only
3406E, C-10, C-12, C-15, C-16 Truck Engines Cylinder Head Grounding Stud - Inspect/Clean/Tighten
3406E, C-10, C-12, C-15, C-16 Truck Engines Engine Oil Level - Check
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Assemble
3408E and 3412E Engines for Caterpillar Built Machines Bearing Clearance - Check
3306B Industrial Engine Piston Cooling Jets - Remove and Install
3176C and 3196 Industrial Engines Belt Tensioner
3306C Truck Engine Crankshaft - Remove
3306C Truck Engine Crankshaft - Install
3176C and 3196 Engines for Caterpillar Built Machines Engine Oil Filter Base
G3612 and G3616 Engines Air Starting System
G3606 and G3608 Engines Lubrication System
Electronic Modular Control Panel II (EMCP II) for EUI Engines Component Location
Electronic Modular Control Panel II (EMCP II) for EUI Engines EMCP Electronic Control (Generator Set)
C-10 and C-12 Truck Engines Air Inlet and Exhaust System