IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Caterpillar


Tilt Lever (Rear) - Remove and Install

Usage:

IT14G 1WN

拆卸步骤

开始:

  1. 连接转向机架锁。 请参考拆解和装配, "转向机架锁 - 分离和连接"。

------ WARNING! ------

拆下连杆销后孔内可能有粘连,突然分离可导致人员伤害。

释放所有液压压力,并确保铲斗和/或附件处于稳定水平的位置。


  1. 将任何附件工具从连接器组件上拆下。

  1. 将提升臂降到地面。

  1. 释放液压系统压力。 请参考拆解和装配, "液压系统压力 - 释放"。



    图 1g00467496

  1. 将适当的起吊设备连接到倾斜油缸 (2) 上。 将木块放在倾斜油缸 (2) 和提升臂 (4) 之间。 拆下螺栓 (3) 。 下板 (1) 。



    图 2g00467497

  1. 拆下螺栓 (6) 和销组件 (5) 。 将倾斜油缸 (2) 降到木块上。



    图 3g01068090

  1. 拆下螺栓 (7) 。 拆下两个板 (8) 。

  1. 拆下内侧倾斜操纵杆 (9) 。 内侧倾斜操纵杆 (9) 的重量约为 19 kg (40 lb)。



    图 4g01068091

  1. 拆下螺栓 (12) 和销组件 (13) 。 降下连杆组件 (15) ,以清除外侧倾斜操纵杆 (14) 。

  1. 拆下螺栓 (10) 。

  1. 拆下销组件 (11) 。 将外侧倾斜操纵杆 (14) 从提升臂上拆下。 外侧倾斜操纵杆 (14) 的重量约为 19 kg (40 lb)。

安装步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     5P-0960     含钼润滑脂        

    注: 组装前,确保销组件可在销孔中自由滑动。 使用工具 (A) 润滑所有的销孔和销。




    图 5g01068091

  1. 放置外侧倾斜操纵杆 (14) ,然后安装销组件 (11) 。 外侧倾斜操纵杆 (14) 的重量约为 19 kg (40 lb)。 安装螺栓 (10) 。

  1. 安置连杆总成 (15) ,以将连杆组件和外侧倾斜操纵杆 (14) 对准。 安装销组件 (13) 。 安装螺栓 (12) 。



    图 6g01068090

  1. 安装内侧倾斜操纵杆 (9) 。 内侧倾斜操纵杆 (9) 的重量约为 19 kg (40 lb)。

  1. 安装两个板 (8) 和螺栓 (7) 。



    图 7g00467497

  1. 安置倾斜油缸 (2) 以对准孔。 安装销组件 (5) 。 安装螺栓 (6) 。



    图 8g00467496

  1. 安置倾斜油缸 (2) 以对准孔。 安装板 (1) 和螺栓 (3) 。 将木块从提升臂 (4) 上拆下。

End By: 分离转向机架锁。 请参考 拆解和装配, "转向机架锁 - 分离和连接"。

Caterpillar Information System:

980G Wheel Loader Braking System Parking Brake Control Cable
793C Off-Highway Truck Machine Systems Service and Parking Brake (Rear) - Assemble
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Propel Hydraulic System
D250E Series II and D300E Series II Articulated Trucks Machine Systems Check and Pressure Reducing Valve (Brake Accumulator) - Remove
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pin Coupler Cylinder - Remove and Install
572R Pipelayer Hydraulic System Pilot Control Valve (Three-Way)
AP-1055B and BG-2455C Asphalt Pavers Conveyor Drive Chains (Drag) - Adjust
AP-1055B and BG-2455C Asphalt Pavers Auger Conveyors - Lubricate - Lubricate the Fittings
CP-563D, CS-563D, CS-573D and CS-583D Vibratory Compactors Propel System Piston Pump (Drum Propel)
AP-1055B and BG-2455C Asphalt Pavers Capacities (Refill)
AP-1055B and BG-2455C Asphalt Pavers Parking Brake Manual Release
AP-1055B and BG-2455C Asphalt Pavers Stopping the Engine if an Electrical Malfunction Occurs
65E, 75E, 85E and 95E Agricultural Tractors After Starting Engine
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Attachment Positioner Control - Remove and Install
DASA 280 Measuring and Control System Control Unit
DASA 280 Measuring and Control System Hand Control Keypads
966G Wheel Loader and 972G Wheel Loader Braking System Parking Brake Actuator
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Design
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Oil Filter Base - Remove and Install
980G Wheel Loader Braking System Parking Brake
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Tilt Cylinder - Remove
789C Off-Highway Truck Plate Locations and Film Locations
784C and 785C Off-Highway Truck/Tractors Battery Disconnect Switch
789C Off-Highway Truck Capacities (Refill)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.