Stick - 2500 mm (98.4 inch)
Show/hide table
Illustration 1 | g00384832 |
(A) Bucket cylinder. (B) Bucket Linkage. (C) Bucket. (D) Stick cylinder. (E) Boom. |
Note: All bores must be free of paint. Coat all bores for pins with lubricant.
(1) Torque for two bolts ... 460 ± 60 N·m (340 ± 44 lb ft)
(2) Use the necessary shims to adjust the lateral clearance.
- Maximum clearance ... 1.0 mm (.04 inch)
- 133-2427 Shim thickness ... 0.5 mm (.02 inch)
- 093-0090 Shim thickness ... 1.0 mm (.04 inch)
- 093-0122 Shim thickness ... 2.0 mm (.08 inch)
- 133-2427 Shim thickness ... 0.5 mm (.02 inch)
(3) Lubricate the sealing lip slightly with the lubricant that is being sealed.
(4) Two 137-2993 Sleeve Bearings
- Outside diameter ... 140.170 + 0.025 - 0.000 mm (5.5185 + 0.0010 - 0.0000 inch)
- Inside diameter ... 120.320 ± 0.020 mm (4.7370 ± 0.0008 inch)
- Install the bearing in the bearing bore. ... 9.5 ± 0.8 mm (.37 ± .03 inch)
- Inside diameter ... 120.320 ± 0.020 mm (4.7370 ± 0.0008 inch)
(5) Two 130-4360 Pin Assembly
- Diameter after plating ... 99.850 ± 0.040 mm (3.9311 ± .0016 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
- Bore diameter for pin ... 100.043 ± 0.043 mm (3.9387 ± .0017 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
(6) Two 4I-6897 Sleeve Bearings
- Outside diameter ... 95.180 ± 0.013 mm (3.7472 ± .0005 inch)
- Inside diameter ... 80.25 ± 0.02 mm (3.159 ± .001 inch)
- Install the bearing in the bearing bore. ... 7.5 ± 0.8 mm (.30 ± .03 inch)
- Inside diameter ... 80.25 ± 0.02 mm (3.159 ± .001 inch)
(7) Two 134-8943 Sleeve Bearings
- Outside diameter ... 130.240 ± 0.013 mm (5.1275 ± 0.0005 inch)
- Inside diameter ... 110.30 ± 0.02 mm (4.343 ± 0.001 inch)
- Install the bearing in the bearing bore. ... 9.5 ± 0.8 mm (.37 ± .03 inch)
- Inside diameter ... 110.30 ± 0.02 mm (4.343 ± 0.001 inch)
Note: Assemble bearings with the groove to the inside of the boss. Assemble bearings with the groove at the top (± 5 degrees) of the bore.
Caterpillar Information System:
345B Excavator Machine Operation Information
A7 Auger General Hazard Information
311B and 312B Excavators Hydraulic System Gear Pump (Pilot) - Test - 311B
345B Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
317B L and 317B LN Excavator Fuses - Replace
C4.4 (Mech) Industrial Engine Troubleshooting
311B and 312B Excavators Hydraulic System Gear Pump (Blade) - Test - 312B and 312B L
M312 Excavator Machine System Boom Cylinder Lines
M312 Excavator Machine System Boom Lines - Variable Adjusting
3406C Engines for Caterpillar Built Machines Cylinder Liner
M312 Excavator Machine System Boom Lines - One Piece
M312 Excavator Machine System Auxiliary Hydraulic Lines - Boom (Variable Adjusting)
318B L and 318B LN Excavator Shipping Specifications
P16, P20, P25, P28, P40 and P60 Pulverizer Crushing Prevention and Cutting Prevention
5130 Excavator Hydraulic System Screen (Implement High Pressure)
312B Excavator Attachments Two Pump Operation
5230 Excavator Hydraulic System Pump Drive
A7 Auger Fire Prevention and Explosion Prevention
5230 Excavator Hydraulic System Relief Valve (Margin)
S25/S225, S30/S230, S40/S240, S50/S250, S80/S280 and S130/S2130 Demolition and Scrap Shears Operation
312B Excavator Attachments Combined Function Hydraulic Operation
A7 Auger Maintenance Interval Schedule
5130 Excavator Hydraulic System Screen (Swing High Pressure)
A7 Auger Auger Bit