Front Idler - Disassemble
Disassembly Procedure
Start By:
- Remove the front idler, the recoil spring and the hydraulic track adjuster as a unit. Refer to Disassembly and Assembly, "Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install" in this manual.
- Thoroughly clean the outside of the front idler prior to disassembly.
- Remove the fill/drain plug from the front idler. Drain the oil from the idler into a suitable container for disposal. The capacity of the idler is 180 mL (6.12 oz).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Put the front idler on one side, as shown. The weight of the front idler is 109 kg (240 lb).
Show/hide table
Illustration 1 | g00483026 |
- Remove two spring pins (1) from bearings (2). Fasten a hoist to two bearings (2). Remove the bearings from the shaft of the front idler. The weight of each bearing is approximately 18 kg (40 lb).
- Remove Duo-cone seal kits (3) from bearings (2) .
Show/hide table
Illustration 2 | g00483027 |
- Remove shaft (5) from the front idler.
Show/hide table
Illustration 3 | g00483028 |
- Remove two O-ring seals (4) from shaft (5) .
Show/hide table
Illustration 4 | g00483029 |
- Remove Duo-cone seal kit (6) from each side of the front idler.
Show/hide table
Illustration 5 | g00483030 |
- Remove bushings (7) from each side of the idler.
Show/hide table
Illustration 6 | g00483031 |
Caterpillar Information System:
M318 and M320 Excavators Machine System Specifications Stabilizer
315B Excavator Machine Systems Main Hydraulic Pump - Disassemble
315B Excavator Machine Systems Main Hydraulic Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod
315B Excavator Machine Systems Main Hydraulic Pump - Remove
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod and Main Bearing Journals
315B Excavator Machine Systems Gear Pump (Pilot) - Remove and Install
330B Excavator Hydraulic System Relief Valve (Line) - Test and Adjust
M315 Excavator Machine System Boom - 3.7 m (12.14 ft)
315B Excavator Machine Systems Solenoid Valve (Proportional Reducing) - Remove and Install
M318 Excavator Hydraulic System Engine Performance - Test
M312 Excavator Hydraulic System Engine Performance - Test
315B Excavator Machine Systems Pilot Valve (Travel) - Remove
315B Excavator Machine Systems Front Idler - Assemble
M312 Excavator Machine System Bucket
330B Excavator Hydraulic System Pump Control (Negative Flow) - Test
M312 Excavator Machine System Bucket
315B Excavator Machine Systems Recoil Spring - Disassemble
307B Excavator Implement Control Pedal - If Equipped
345B Excavator Shipping Specifications
M312 Excavator Machine System Bucket - Ditch Cleaning, Rigid
M312 Excavator Machine System Bucket - Ditch Cleaning, Adjustable
315B Excavator Machine Systems Main Hydraulic Pump - Assemble
330B Excavator Hydraulic System Piston Pump (Main) - Test