Parking Brake Release Oil Filter - Replace
Show/hide table
Illustration 1 | g00351572 |
Show/hide table
Illustration 2 | g00322955 |
- Remove the drain plug from the bottom of the filter housing. Drain the oil into a suitable container. Clean the drain plug and install the drain plug.
Note: Removing the drain plug from the bottom of the filter housing may not drain all of the oil from the filter.
Show/hide table
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Remove the filter housing and the filter element. Discard the used filter element.
- Wash the filter housing in clean, nonflammable solvent.
- Inspect the seal in the housing base. If the seal is damaged, replace the seal with a new seal.
- Install the new element in the filter housing.
- Install the filter housing.
- Start the engine and operate at low idle. Check for leaks and make any necessary repairs.
- Observe the oil level. The transmission must be in the NEUTRAL position and the parking brake must be engaged.
- Maintain the oil level to the FULL COLD mark in the sight gauge.
Show/hide table
Illustration 3 | g00324184 |
- If necessary, add oil.
Caterpillar Information System:
3306C Engines for Caterpillar Built Machines Automatic Timing Advance Unit
789C Off-Highway Truck Air/Hydraulic Cylinder Breather - Clean
740 Articulated Truck, 768C, 769C, 769D, 772B, 773B, 773D, 773E, 773F, 776, 776B, 776C, 776D, 777, 777B, 777C, 777D, 777F, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C and 793D Off-Highway Trucks and 771C, 771D, 775B, 775 Machine Preparation for Troubleshooting
789B Off-Highway Truck Hydraulic System Hoist Control - Adjust
793B Off-Highway Truck Hoist, Torque Converter and Brake Tank Oil Level - Check
793B Off-Highway Truck Window - Clean
793B Off-Highway Truck Dimmer and Horn Switch
793B Off-Highway Truck Hoist, Torque Converter and Brake Tank Oil - Change
3500 Generator Sets Engine Crankcase Breather - Clean
416C, 426C, 428C, 436C and 438C Backhoe Loaders Hydraulic and Steering System Control Valve (Swing)
793B Off-Highway Truck Hoist, Torque Converter and Brake Tank Suction Screen - Inspect/Clean/Replace
793B Off-Highway Truck Hoist Screens - Clean
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Hydraulic System Oil Level - Check
793B Off-Highway Truck Hydraulic System Hoist Cylinder Performance - Test
793B Off-Highway Truck Window Wiper - Inspect/Replace
966G and 972G Wheel Loaders Power Train Relief Valve (Transmission Hydraulic Control) - Assemble
416C, 426C, 428C, 436C and 438C Backhoe Loaders Hydraulic and Steering System Control Valve (Boom)
793B Off-Highway Truck Service Brakes - Inspect
793B Off-Highway Truck Steering Accumulator - Check
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Fuses - Replace
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Modulating Valve (Transmission Clutch) - Remove
793B Off-Highway Truck Steering System Oil - Change
793B Off-Highway Truck Steering System Oil Level - Check
550, 570 and 580 Wheel Harvesters Operating Technique Information