3500B and 3500B High Displacement Generator Set Engines Caterpillar


Lubrication System Operation

Usage:

3508 1ZF



图 1g00322483

主机油泵和润滑系统示意图(典型示例)

(1) 主油道

(2) 左凸轮轴油道

(3) 活塞冷却喷嘴油道

(4) 活塞冷却喷嘴油道

(5) 右凸轮轴油道

(6) 机油供油管

(7) 顺序阀

(8) 顺序阀

(9) 接头

(10) 发动机机油滤清器旁通阀

(11) 发动机机油冷却器

(12) 发动机机油冷却器旁通阀

(13) 机油泵安全阀

(14) 发动机机油泵

(15) 弯头

(16) 吸油喇叭口

(17) 发动机机油滤清器壳体

本系统使用的发动机机油泵 (14) 具有三组泵齿轮。 这些泵齿轮由前齿轮系驱动。 发动机机油泵 (14) 将发动机机油从油底壳中吸出,然后使其流过吸油喇叭口 (16) 和弯头 (15) 。 吸油喇叭口 (16) 内有一个滤网,用来清洁发动机机油。

发动机机油泵内有一个机油泵安全阀 (13) 。 机油泵安全阀控制来自发动机机油泵的发动机机油压力。 这将使不需要的发动机机油能够流回到发动机机油泵的进油道。

发动机机油泵将机油送过发动机机油冷却器 (11) 和发动机机油冷却器,然后使其流至缸体中主油道 (1) 和左凸轮轴油道 (2) 。 发动机机油冷却器 (11) 在将发动机机油输送到滤清器之前降低其温度。

如果发动机机油冷却器 (11) 堵塞或发动机机油粘度高得使油压之差增加 180 ± 20 kPa (26 ± 3 psi),则发动机机油冷却器旁通阀 (12) 允许发动机机油直接流至滤清器。

发动机机油滤清器位于发动机前部上的发动机机油滤清器壳体 (17) 中。 发动机机油滤清器壳体中有一个单独的旁通阀。

来自滤清器的清洁发动机机油通过接头 (9) 进入缸体中。 一部分发动机机油流到左凸轮轴油道 (2) 。 其余的发动机机油流到主油道 (1) 。

左凸轮轴油道 (2) 和右凸轮轴油道 (5) 通过钻孔与每一个凸轮轴轴承相连。 发动机机油流过每一个凸轮轴轴颈的周围。 发动机机油接着流经缸盖和摇臂壳体,然后流至摇臂轴。 一个钻孔将气门挺柱孔与摇臂轴的油孔相连通。 气门挺柱在达到每个行程的顶部时得到润滑。

主油道通过钻孔与主轴承相连。 曲轴内的钻孔将主轴承的供油通到连杆轴承。 来自主油道后端的发动机机油流到右凸轮轴油道的后端。

顺序阀 (7) 和顺序阀 (8) 允许发动机机油从主油道流至活塞冷却喷嘴油道 (3) 和 (4) 。 此顺序阀在机油压力大约为 130 kPa (19 psi) 时开始开启。 直到主油道内的机油有足够压力时,顺序阀才允许发动机机油流入活塞冷却喷嘴油道。 这就减少了发动机起动时建立机油压力所需的时间量。 这也有助于在怠速时保持机油压力。




图 2g00281794

活塞冷却和润滑(典型示例)

(18) 活塞冷却喷嘴

每一个活塞下面都有一个活塞冷却喷嘴 (18) 。 每一个冷却喷嘴都有两个开口。 一个开口朝向活塞底部的油道。 此油道将发动机机油送到活塞环带后面的歧管内。 两个活塞环孔的侧面上都有一个开槽(凹槽)。 此开槽与环带后的歧管相连。 另一个开口朝向活塞中央。 这有助于冷却活塞并为活塞销提供润滑。




图 3g00322503

涡轮增压器(典型示例)

(6) 机油供油管

(19) 机油排油管

机油供油管 (6) 将来自后接头的机油输送至涡轮增压器。 机油排油管 (19) 在发动机每一侧上都与飞轮壳体相连。

发动机通过钻孔油道输送至前和后齿轮总成。 钻孔油道位于前壳体、后壳体和缸体的端面中。 这些油道连接至左凸轮轴油道 (2) 和右凸轮轴油道 (5) 。

在发动机机油流过润滑系统后,发动机机油返回发动机油底壳。

Caterpillar Information System:

3508, 3512, and 3516 Generator Sets Generator Set Description
3618 Engine Piston and Rings
322B Excavator Hydraulic System General Testing and Adjusting Information
G3500 Generator Sets Control Panel
3508, 3512 and 3516 Engines Air Inlet and Exhaust System
PM3412C Power Modules Fuel System Secondary Filter - Replace
SPS342 Skid Mounted Pumper S·O·S Services Coolant Analysis
3512 Industrial Engine Extended Life Coolant (ELC) Cooling System Maintenance
3618 Engine Troubleshooting
3512 Industrial Engine Extended Life Coolant (ELC)
G3612 and G3616 Engines Manual Barring Group - 50:1 Reduction
G3606 and G3608 Engines Cooling System
3508, 3512 and 3516 Engines Basic Block
3508, 3512 and 3516 Engines Electrical System
Instruction For Mounting The Electronic Modular Control Panel II In A Remote Location{4490} Instruction For Mounting The Electronic Modular Control Panel II In A Remote Location{4490}
G3606 and G3608 Engines Electrical System
3516B Generator Set Engines with Dynamic Gas Blending Cooling System Operation - Jacket Water Aftercooled
3508, 3512 and 3516 Engines Fuel System
G3500 Engines Gauges and Indicators
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Shutoff
3306B Industrial Engine Fuel Control Linkage - Check/Lubricate
3508, 3512, and 3516 Generator Sets Model View Illustrations
G3500 Engines Performance Parameters
Electronic Modular Control Panel II (EMCP II) For MUI Engines Hourmeter Programming OP7
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.