Piston and Rings
Show/hide table
 | |
| Illustration 1 | g00308090 |
Show/hide table
| Piston and Rings | |||
| (1) Top Ring | (2) Intermediate Ring | (3) Oil Control Ring | |
| Width Of Groove In New Piston | 6.160 to 6.190 mm (.2425 to .2437 inch) | 6.160 to 6.190 mm (.2425 to .2437 inch) |
8.060 to 8.090 mm (.3173 to .3185 inch) |
| Width Of Piston Ring | 5.975 to 5.990 mm (.2352 to .2358 inch) |
5.975 to 5.990 mm (.2352 to .2358 inch) |
7.914 to 7.936 mm (.3116 to .3124 inch) |
| Clearance Between Groove And Piston Ring | 0.170 to 0.215 mm (.0067 to .0085 inch) |
0.170 to 0.215 mm (.0067 to .0085 inch) |
0.124 to 0.176 mm (.0049 to .0069 inch) |
| Piston Ring End Gap In 280 mm (11.0 inch) Bore |
1.00 to 1.20 mm (.039 to .047 inch) |
1.80 to 2.10 mm (.071 to .083 inch) |
0.90 to 1.30 mm (.035 to .051 inch) |
| Installation Procedure | "UP-1" | "UP-2" | (1) |
Show/hide table
| ( 1 ) | Install the oil control ring and the ring expander with the gaps opposite each other. The white colored portion of the ring expander must be visible through the oil control ring gap. |
Bore in piston for piston pin ... 130.059 ± 0.009 mm (5.1204 ± .0004 inch)
Diameter of piston pin ... 129.994 ± 0.006 mm (5.1179 ± .0002 inch)
Caterpillar Information System:
322B Excavator Hydraulic System General Testing and Adjusting Information
G3500 Generator Sets Control Panel
3508, 3512 and 3516 Engines Air Inlet and Exhaust System
PM3412C Power Modules Fuel System Secondary Filter - Replace
SPS342 Skid Mounted Pumper S·O·S Services Coolant Analysis
3512 Industrial Engine Extended Life Coolant (ELC) Cooling System Maintenance
3618 Engine Troubleshooting
3512 Industrial Engine Extended Life Coolant (ELC)
G3612 and G3616 Engines Manual Barring Group - 50:1 Reduction
G3606 and G3608 Engines Cooling System
3406E, C-10 and C-12 Truck Engines Fuel System Primary Filter - Clean/Replace
3618 Engine Engine Design
3508, 3512, and 3516 Generator Sets Generator Set Description
3500B and 3500B High Displacement Generator Set Engines Lubrication System Operation
3508, 3512 and 3516 Engines Basic Block
3508, 3512 and 3516 Engines Electrical System
Instruction For Mounting The Electronic Modular Control Panel II In A Remote Location{4490} Instruction For Mounting The Electronic Modular Control Panel II In A Remote Location{4490}
G3606 and G3608 Engines Electrical System
3516B Generator Set Engines with Dynamic Gas Blending Cooling System Operation - Jacket Water Aftercooled
3508, 3512 and 3516 Engines Fuel System
G3500 Engines Gauges and Indicators
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Shutoff
3306B Industrial Engine Fuel Control Linkage - Check/Lubricate
3508, 3512, and 3516 Generator Sets Model View Illustrations