Final Drive and Wheel
Show/hide table
Illustration 1 | g01358222 |
(1) Torque for 15 studs on the right hand side ... 102 ± 14 N·m (75 ± 10 lb ft)
(2) Lubricate all O-rings with the lubricant that is being sealed prior to assembly.
(4) Torque the bolts initially in an alternating star pattern to 300 ± 60 N·m (221 ± 44 lb ft). Torque the bolts in an alternating star pattern to 430 ± 60 N·m (317 ± 44 lb ft).
(5) 6G-8370 Shim Pack
- Assembled thickness of shims ... 2.97 ± 0.08 mm (0.117 ± 0.003 inch)
- Thickness of one shim out of nine shims ... 0.250 ± 0.013 mm (0.0098 ± 0.0005 inch)
- Thickness of one shim out of nine shims ... 0.080 ± 0.013 mm (0.003 ± 0.0005 inch)
- Inside diameter ... 108.0 mm (4.25 inch)
- Outside diameter ... 158.0 mm (6.22 inch)
- Thickness of one shim out of nine shims ... 0.250 ± 0.013 mm (0.0098 ± 0.0005 inch)
Note: The shim pack must be flat and free of dents and wrinkles.
(6) Torque for 12 bolts ... 280 ± 30 N·m (207 ± 22 lb ft)
Note: Use bolt pattern (3) that is shown above in order to tighten bolts (6) .
(7) Torque for two valve stems ... 8.5 ± 0.6 N·m (75.00 ± 5.00 lb in)
Caterpillar Information System:
994D Wheel Loader Automatic Lubrication System General Information
621F, 623F and 627F Wheel Tractor-Scrapers Air System and Brakes Service Brake Control Valve
3054 Engine Rocker Shaft
637E Wheel Tractor-Scraper Wheel Scraper Power Train Relief Valve (Transmission Lubrication) - Scraper
621F and 627F Wheel Tractor-Scrapers Hydraulic System Apron Cylinder
994D Wheel Loader Steering System Steering Control Valve
Caterpillar Monitoring System Tattletale Mode
621F and 627F Wheel Tractor-Scrapers Hydraulic System Bowl Cylinder
IT14G Integrated Toolcarrier Starting Above 0°C (32°F)
IT14G Integrated Toolcarrier Walk-Around Inspection
IT14G Integrated Toolcarrier Bucket Kickout and Positioner Control
3406E and 3456 Engines for Caterpillar Built Machines Compression Brake
994 Wheel Loader Power Train Transmission Lubrication
994D Wheel Loader Steering System Filter (Steering Pump Case Drain)
Caterpillar Monitoring System Units Mode
Caterpillar Monitoring System Setup Mode
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Fuel Tank (Center) - Remove
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Fuel Tank (Center) - Install
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Fuel Tank (Left Side) - Remove
633E Series II Wheel Tractor-Scraper Hydraulic System Ejector Cylinder
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Fuel Tank (Left Side) - Install
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Fuel Tank (Right Side) - Remove
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Fuel Tank (Right Side) - Install
IT14G Integrated Toolcarrier Machine Operation Information