Ejector Blade Floor Rollers - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件说明 | 数量 |
B | 1P-0510 | 起子总成 | 1 |
C | 7X-7699 | 润滑脂 | 1 |
- 清洁并检查所有零件。 如果任何零件磨损或损坏,则应使用 Caterpillar 新件进行更换。
Show/hide table
图 1 g01188833 - 使用工具 (B) 在壳体 (11) 中安装唇形密封 (13)。
Show/hide table
图 2 g01195296 - 将壳体安装到支架 (3) 上前,将工具 (C) 涂敷在壳体 (11) 上的唇形密封 (13)。
Show/hide table
图 3 g01188834 - 将轴承内圈 (12) 安装到底板滚轮上,使轴承内圈上的台肩朝向支架 (3)。
Show/hide table
图 4 g01188835 - 将工具 (C) 涂敷在轴承内圈 (12) 和壳体 (11) 之间的轴承腔内。
Show/hide table
图 5 g00896615 - 安装滚柱轴承 (9)。
Show/hide table
图 6 g01195297 - 将 O 形密封圈 (7) 安装到壳体 (11) 和滚柱轴承 (9) 上。
Show/hide table
图 7 g01188836 - 将工具 (C) 涂覆到滚柱轴承 (9) 上。
Show/hide table
图 8 g00896631 - 将内板 (8) 安装到滚柱轴承 (9) 上。
Show/hide table
图 9 g00926131 - 将 O 形密封圈 (6) 安装到支架 (3) 上。
Show/hide table
图 10 g00926132 - 将盖 (2) 安装到支架 (3),再用螺栓 (1) 将盖固定到位。
Show/hide table
图 11 g01188837 - 使用工具 (B) 将唇形密封 (10) 安装到底轮 (5) 中。
Show/hide table
图 12 g00926133 - 将工具 (C) 涂敷到底轮 (5) 上的唇形密封 (10) 上,再将底轮安置到壳体 (11) 上。 拆下三个螺栓 (4) 和垫圈。 等量拧紧螺栓,以将底轮拉拔到壳体上。
Show/hide table
图 13 g00896633 - 安装其余的螺栓 (4) 和垫圈,以将底轮 (5) 固定到壳体 (11) 上。
Show/hide table
图 14 g00926134 - 重复步骤 2 至 14 以安装支架 (3) 相对侧的轮子。
结束:
- 将推料器铲刀底板滚轮安装到机器上。 请参阅拆解和组装, "推料器铲刀底板滚轮 - 安装"。
Caterpillar Information System:
RM-250C, RR-250B and RM-350B Additive Spray System Additive Spray System - Clean
793C XQ Off-Highway Truck Specifications
D5N Track-Type Tractor Power Train Power Train Oil Pump
730 EJECTOR and 740 EJECTOR Articulated Trucks Ejector Blade Floor Rollers - Disassemble
R1600 Load Haul Dump Hydraulic System Hydraulic Tank and Filter
RM-250C, RR-250B and RM-350B Additive Spray System Circuit Breakers - Reset
247 and 257 Multi Terrain Loaders Machine Systems Diverter Valve - Remove and Install
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Connector Locations
CP-533C, CP-563C, CS-533C, CS-563C, CS-573C and CS-583C Paving Compactors Propel System Piston Motor (Drum Propel)
CB-634D Vibratory Compactor Machine Systems Water Spray System Troubleshooting
554 Forwarder and 574 Forwarder Log Loader Pillar Base Mounting Bolt - Inspect/Tighten/Replace
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Connector Contact Description
793C XQ Off-Highway Truck Suspension Cylinder - Check
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Speed Limiting Function
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Hydraulic Tank
928H and 928HZ Wheel Loader Steering System Oil Filter (Hydraulic)
PM-465 Cold Planer Compressed Air System Air Filter Element - Clean/Replace
Flexxaire Fan Calibration
834G Wheel Dozer and 836G Landfill Compactor Power Train Torque Converter Impeller Clutch Pressure - Test
R1700G Load Haul Dump Caterpillar Monitoring System
2002/08/01 Engine Tool Lists And Machine Tool Lists Are Available On The CaterpillarIntranet {0600}
3408E and 3412E Engines for Caterpillar Built Machines Injector Solenoid Circuit - Test
RM-250C, RR-250B and RM-350B Additive Spray System Additive Spray System Strainer - Clean
834G Wheel Dozer and 836G Landfill Compactor Power Train Torque Converter Lockup Clutch Pressure - Test