Traction Control Valve - Assemble
- 检查所有 O 形密封圈和部件是否磨损或损坏。 如有必要,请更换部件。
- 用少量密封的润滑剂润滑所有 O 形密封圈。
Show/hide table
图 1 g00506789 - 安装滚珠 (55) 和垫圈 (56)。
Show/hide table
图 2 g00506779 - 安装定位销 (54)。
- 安装弹簧 (53) 和 (52)。
Show/hide table
图 3 g00506777 - 将缓动阀 (51) 装入滑阀 (50)。
Show/hide table
图 4 g00506676 - 安装滑阀组件 (50)。
Show/hide table
图 5 g00506671 - 安装 O 形密封圈 (49)。
Show/hide table
图 6 g00506670 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 放置盖组件 (48),如图所示。 安装 5 只螺栓 (47) 和垫圈。
Show/hide table
图 7 g00506663 - 如有必要,将弹簧销 (46) 安装到负载活塞 (45) 中。
Show/hide table
图 8 g00506667 - 安装活塞 (45)。
Show/hide table
图 9 g00506612 - 安装弹簧 (44)。
Show/hide table
图 10 g00506607 - 将滑阀 (42) 安装到缓动阀 (43) 中。
Show/hide table
图 11 g00506603 - 安装滑阀组件 (42)。
- 安装 O 形密封圈 (41)。
Show/hide table
图 12 g00506577 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 放置盖 (40) 和夹子 (39),如图所示。 安装螺栓 (38)。
Show/hide table
图 13 g00506570 - 将 O 形密封圈 (37) 安装在适配器 (35) 上。
Show/hide table
图 14 g00506564 - 将 O 形密封圈 (33) 安装到螺塞 (36) 上。
Show/hide table
图 15 g00506563 - 安装适配器 (35)。 将 O 形密封圈 (34) 安装到适配器 (35) 上。
- 安装螺塞 (33)。
Show/hide table
图 16 g00506541 - 将 O 形密封圈 (32) 安装到每个螺纹接头组件 (31) 上。
Show/hide table
图 17 g00506540 - 安装螺纹接头组件 (31)。
Show/hide table
图 18 g00506537 - 安装防尘盖 (30)。
Show/hide table
图 19 g00506533 - 将 O 形密封圈 (29) 安装到歧管 (28) 上。
Show/hide table
图 20 g00506531 - 放置歧管 (28) 和夹子 (27),如图所示。 安装螺栓 (26)。
Show/hide table
图 21 g00506524 - 将 O 形密封圈 (22)、 (21)、 (20) 和 (19) 安装到芯组件 (18) 上。
注: 支承环位于 O 形密封圈的每侧。
- 将支承环 (25)、 (24) 和 (23) 安装到芯组件 (18) 上。
Show/hide table
图 22 g00506519 - 安装芯组件 (18)。 拧紧芯组件 (18) 至扭矩为
30 ± 5 N·m (22 ± 4 lb ft) 。Show/hide table图 23 g00506510 - 放置线圈组件 (17),如图所示。 安装锁紧螺母 (16) 和弹簧。 拧紧锁紧螺母 (16) 至扭矩为
16 ± 2 N·m (141.61 ± 17.7 lb in) 。Show/hide table图 24 g00506507 - 将滤网 (14) 和 O 形密封圈安装到电磁阀 (11) 中。
- 将螺塞 (15) 和 O 形密封圈安装到电磁阀 (11) 中。
Show/hide table
图 25 g00506429 - 安装 O 形密封圈 (13)。
Show/hide table
图 26 g00506428 - 放置电磁阀 (11) 和夹子,如图所示。 安装螺栓 (12)。
Show/hide table
图 27 g00506427 - 安装管塞组件 (10)。
- 安装管塞 (9)。
Show/hide table
图 28 g00506426 - 将 O 形密封圈 (7) 安装到挡圈 (6) 中。
- 将滤网组件 (8) 安装到挡圈 (6) 中。
Show/hide table
图 29 g00506425 - 放置挡圈 (6),如图所示。
Show/hide table
图 30 g00506424 - 如有必要,安装弹簧销 (5)。
- 将 O 形密封圈 (4) 安装到盖 (3) 中。
Show/hide table
图 31 g00506423 - 放置盖组件 (2),如图所示。 安装 2 只螺栓 (1)。
注: 清洁度是一项重要的因素。 执行组装步骤之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。
结束:
- 安装牵引控制阀。 请参阅拆解和组装, "牵引控制阀 - 安装"。
Caterpillar Information System:
TK711, TK721, TK722 and TK732 Track Feller Bunchers Battery - Recycle
784C and 785C Off-Highway Trucks Machine Systems Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission) - Remove
Caterpillar Monitoring System Display Components
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Evaporator Coil - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0271 FMI 03 Alarm (Action) Voltage Above Normal - Test
631E Series II Wheel Tractor-Scrapers Backup Alarm - Test
583R Pipelayer Power Train Transmission - Assemble
3114, 3116 and 3126 MUI Engine Governors Governor Speed Circuit
966G Wheel Loader and 972G Wheel Loader Power Train CID 0622 FMI 04 Push Button Switch (Upshift) Voltage Below Normal - Test
980G Wheel Loader Power Train Output Transfer Gears - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Housing (Front)
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Heater Coil - Remove and Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Brake Accumulator - Remove
Charging System Troubleshooting {1406} Charging System Troubleshooting {1406}
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0824 FMI 03 Lamp (Green Payload) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0824 FMI 05 Lamp (Green Payload) Current Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0824 FMI 06 Lamp (Green Payload) Current Above Normal - Test
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Piston Pump (Implement) - 550 Wheel Harvester
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hoist Cylinder - Disassemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0825 FMI 03 Lamp (Red Payload) Voltage Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0825 FMI 05 Lamp (Red Payload) Current Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0825 FMI 06 Lamp (Red Payload) Current Above Normal - Test
3406E On-Highway Engine Pistons and Connecting Rods - Disassemble
Caterpillar Monitoring System Gear Display Mode