Electric Starting Motor - Remove and Install
Show/hide table
Disconnect batteries before performance of any service work. |
Note: Before disconnecting the cable assemblies, mark the items for the proper connections in order to ensure correct assembly.
- Disconnect the cable assemblies (1) from electric starting motor (2).
This part number has three electric starting motors. Disconnect the cable assemblies between all three electric starting motors.
- Attach a suitable lifting device to electric starting motor (2). The weight of the electric starting motor is
19.5 kg (43 lb) .Show/hide tableIllustration 2 g06113164 - Disconnect the cable assemblies (1) from the electric starting motor (2) on the opposite side of the engine.
- Attach a suitable lifting device to electric starting motor (2). The weight of the electric starting motor is
19.5 kg (43 lb) .Show/hide tableIllustration 3 g06113452 - Remove Bolts (3) and (4 and remove electric starting motor.)
Show/hide table
Illustration 4 g06113501 - Remove bolts (3) and electric starting motor (2).
Show/hide table
Illustration 1 | g06112998 |
- Inspect the gasket for the joint between the electric starting motor and the flywheel housing. Obtain a new gasket, if necessary.
Show/hide table
Illustration 5 g06113567 - Install electric starting motor (2) and cable assemblies (1) in reverse order of removal.
- Tighten nuts (5) and (6) to a torque of
35. ± 5 N·m (26 ± 4 lb ft) .
- Tighten nuts (5) and (6) to a torque of
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Machine Systems Control Manifold - Remove and Install - Cutter Box
C4.4 and C6.6 Engines Exhaust Has Excessive White Smoke
C18 Marine Auxiliary and Marine Generator Set Engines Electrical Connectors
C175-16 IMO III Offshore Engine Housing (Front)
797F and 797F XQ Off-Highway Trucks Machine Systems Air Dryer - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Control Manifold - Remove and Install - Conveyor
C18 Marine Auxiliary and Marine Generator Set Engines Component Location
C175-16 IMO III Offshore Engine Turbocharger Support
C175-16 IMO III Offshore Engine Thermocouple
C175-16 IMO III Offshore Engine Generator Coupling
PM820, PM822, and PM825 Cold Planer Machine Systems Control Manifold - Remove and Install - Grade Control Ski
PM820, PM822, and PM825 Cold Planer Machine Systems Control Manifold - Remove and Install - Right Side
Selective Catalytic Reduction Retrofit Aftertreatment Test ECM Mode - Cat Emissions Solutions Commissioning
C18 Marine Auxiliary and Marine Generator Set Engines Cat Data Link - Test
C18 Marine Auxiliary and Marine Generator Set Engines Coolant Level - Test
C18 Marine Auxiliary and Marine Generator Set Engines Electrical Power Supply - Test
C18 Marine Auxiliary and Marine Generator Set Engines Indicator Lamp - Test
C18 Marine Auxiliary and Marine Generator Set Engines Sensor Signal (Analog, Active) - Test
C13 Engines for Caterpillar Built Machines Exhaust Temperature Is High
C175-16 Petroleum Generator Set Engines Engine Operation
A New Engine Oil Filter Element Is Now Used For Certain C175 Engines {1308} A New Engine Oil Filter Element Is Now Used For Certain C175 Engines {1308}
C13 Engines for Caterpillar Built Machines Engine Stalls at Low RPM
Improved Fuel Transfer Pumps Are Used on Certain 3500 Commercial Engines {1256} Improved Fuel Transfer Pumps Are Used on Certain 3500 Commercial Engines {1256}
New Software Is Now Used for Certain C175-16 Engines {1920} New Software Is Now Used for Certain C175-16 Engines {1920}