Cylinder Block
Show/hide table
| |
| Illustration 1 | g03838785 |
|
Front view | |
Show/hide table
| Specification for 353-3970 Cylinder Block Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 3 | 4W-4813 Plug | Torque to |
| A | - | - | Bore in the cylinder block for the camshaft bearings is |
| 2 | 8 | 6V-3348 O-Ring Seal | Lubricate the bore lightly with the fluid that is being sealed. |
| B | 9 | 223-1696 Crankshaft Bearing Cap | Install crankshaft bearing caps with the part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail. |
| Width of the main bearing cap is |
|||
| Width of cylinder block for main bearing cap is |
|||
| C | - | - | New dimension from centerline of crankshaft bearing bore to the top of the block is |
| D | - | - | New dimension from centerline of crankshaft bearing bore to bottom of block (pan rails) is |
| E | - | - | Bore in the block for the main bearings is |
| 3 | 28 | 7X-7925 Bolt | Use the following procedure in order to tighten the crankshaft bearing cap bolts.
1. Lubricate the threads with clean engine oil before assembly. 2. Tighten the bolts by hand. 2. Tighten the bolts in the numerical sequence as shown in Illustration 1 to 3. Again, tighten each bolt in the numerical sequence as shown in Illustration 1 to an additional angle of 180 ± 5 degrees. |
Show/hide table
| |
| Illustration 2 | g03838786 |
|
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 4 | 4 | 5F-9657 O-Ring Seal | Lubricate the bore lightly with the fluid that is being sealed. |
Caterpillar Information System:
G3606 and G3608 Engines Turbocharger - Install
Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.2 {4490, 7610}
3516E Engines for 793D Off-Highway Trucks System Overview
3516E Engines for 793D Off-Highway Trucks Electronic Service Tools
C9.3 Marine Engine Housing (Front) - Remove and Install
C4.4 and C7.1 Engines General Information
C9.3 Marine Engine Fuel Filter Base - Remove and Install - Left-Hand Duplex
3512C and 3516C Industrial Engines Radiator
3512C and 3516C Industrial Engines Electronic Control Module
3512C and 3516C Industrial Engines Electronic Control Module
352F OEM Excavator Based Specialty Solutions Before Operation
PM3516 Power Modules Fire Prevention and Explosion Prevention
3512C and 3516C Industrial Engines Air Inlet and Exhaust Lines
C4.4 and C7.1 Engines Component Location
C4.4 and C7.1 Engines Electrical Connectors
2015/05/28 Cat Reman Announces the Addition of Power Train Components for Mining Trucks {3030, 3258, 4008, 4051, 4201, 4251, 4267}
2015/06/26 New Software Is Used on 3512C Engines in 6060 Hydraulic Shovels {1920}
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Engine Air Filter Element - Clean/Replace
3516B Generator Set Engines with Dynamic Gas Blending Engine Stalls at Low RPM
3516B Generator Set Engines with Dynamic Gas Blending Engine Shutdown Occurs Intermittently
3512C and 3516C Industrial Engines Exhaust Manifold
3512C Generator Set Engine Air Starting Motor - Remove and Install
3516C High Displacement Engine Cooling Fan Control - Test
3516B Generator Set Engines with Dynamic Gas Blending Fuel Consumption Is Excessive