Cylinder Block
Show/hide table
Illustration 1 | g02807876 |
(1) Cylinder Gauge |
Show/hide table
Inside diameter of cylinder block bore (New) | |
Allowable limit | |
Allowable limit for the difference between the maximum and minimum inside diameter | |
Cylinder Correction (Oversize)
Show/hide table
Illustration 2 | g02807996 |
(A) Cylinder Inside Diameter Before Correction
(B) Oversized Inside Diameter |
- If the cylinder wear is more than the allowable limit, bore and hone it to the specified dimension.
Show/hide table
Table 2 Oversized inside diameter of bore (New) 87.250 mm (3.4351 inch) to87.272 mm (3.4359 inch) Allowable limit 87.420 mm (3.4417 inch) Allowable limit for the difference between the maximum oversized inside diameter and the minimum oversized inside diameter of the cylinder 0.15 mm (0.0059 inch)
Note: Replace the pistons and piston rings with oversized pistons.
- Clean the cylinder block surface.
Show/hide table
Illustration 3 g02995540 Show/hide tableIllustration 4 g02995558 - Place a straightedge on the cylinder block four sides (A), (B), (C), (D, and) two diagonal (E), and (F) as shown in the Illustration. Measure the clearance with a feeler gauge.
Show/hide table
Table 3 Cylinder block flatness Allowable limit 0.05 mm (0.002 inch) - If the measurement exceeds the allowable limit, correct the cylinder block with a surface grinder.
Note: Be sure to check the valve recessing after correcting.
Caterpillar Information System:
3512C and 3516C Marine Propulsion Engines Diagnostic Trouble Codes
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pump
2011/12/23 A New Routing Is Used on Fuel Injector Wiring Harnesses on C9.3 Industrial Engines {1290, 1408, 1900}
3516C and C175-16 Engines Selective Catalytic Reduction SCR Module Differential Pressure Is Low
3516C and C175-16 Engines Selective Catalytic Reduction SCR Module Differential Pressure Is High
2011/12/23 A New Bolt and Washers Are Used in the Damper Guard Group of Certain C18 Marine Engines {1205, 7553}
2011/12/23 Proper Measurement for O-Ring Seal Land of Water-Cooled Exhaust Elbows on Certain Commercial Engines {1061}
C18 Generator Set Engine Oil Level Gauge - Calibrate
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies UPS View Software
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Specifications
3516C and C175-16 Engines Selective Catalytic Reduction Air Assist Pressure Is Low
3516C and C175-16 Engines Selective Catalytic Reduction Air Assist Pressure Is High
3512C and 3516C Marine Propulsion Engines Event Codes
Procedures For Using: 127-8781 Transfer Filter Cart , old 9U-7361 (110V, 60 hz), 169-7159 Transfer Filter Cart , old 127-8782 (220V, 50 hz) CE, 174-9158 Transfer Filter Cart , old 129-0849 (Air Motor Driven){0374, 0599, 0680, 0738} Procedures For Using: 127-8781 Transfer Filter Cart , old 9U-7361 (110V, 60 hz), 169-7159 Transfer Filter Cart , old 127-8782 (220V, 50 hz) CE, 174-9158 Transfer Filter Cart , old 129-0849 (Air Motor Driven){0374, 0599, 0680, 0738}
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Modem
UPS 120, UPS 150, UPS 250 and UPS 300 Uninterruptible Power Supplies Ethernet Interface
320 GC, 320 and 323 Excavator Machine Systems Specifications Bucket Linkage
Procedure for Using 173-8839 Fluid Storage Filter Cart {0113, 0374, 0599, 0680, 0738, 7579} Procedure for Using 173-8839 Fluid Storage Filter Cart {0113, 0374, 0599, 0680, 0738, 7579}
3516B Engine for the MT4400D Off-Highway Truck Water Lines
3512C and 3516C Industrial Engines Turbocharger Oil Lines
3516B Engine for the MT4400D Off-Highway Truck Turbocharger Oil Lines
3512C and 3516C Industrial Engines Turbocharger
3512B and 3512C Petroleum Generator Set Engines Engine Speed Sensor
3512E Tier 4 Final Engines for Land Electric Drilling Switches