Rocker Shaft and Push Rod - Remove and Install - G3412B
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-7307     | 发动机盘车工具     | 1     |
B     | FT-1322     | 操纵杆组件     | 1     |
开始:
- 拆下变压器。
- 用工具 (A) 旋转曲轴,释放摇臂上的压力。
Show/hide table
图 1 | g00785957 |
- 用工具 (B) 拆下推杆 (1) 。
- 拆下气门桥 (3) 。 将识别标记放在气门桥上用以定位。
Show/hide table
图 2 | g00785959 |
- 拆下螺栓 (2) 和摇臂轴组件 (4) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-7307     | 发动机盘车工具     | 1     |
B     | FT-1322     | 操纵杆组件     | 1     |
- 将摇臂轴组件 (4) 在发动机上安装到位。
Show/hide table
图 3 | g01422755 |
- 使用清洁的发动机机油润滑固定摇臂轴组件的螺栓 (2) 。 将螺栓 (2) 安装在摇臂轴组件上。
- 使用以下步骤拧紧螺栓。
- 按数字顺序拧紧螺栓 3 至 8 至扭矩为 270 ± 25 N·m (199 ± 18 lb ft)。
Show/hide table图 4 g00789975
- 按数字顺序拧紧螺栓 3 至 8 至扭矩为 450 ± 20 N·m (332 ± 15 lb ft)。
- 再次进行步骤 3b,确保螺栓拧紧到正确扭矩。
- 用清洁的发动机机油润滑气门桥定位销。 将气门桥 (3) 安装在发动机上的原位置。 采用以下步骤调整桥:
- 将清洁的发动机机油机油涂在桥的润滑油道内。
- 旋出调整螺钉。 用 4.5 - 45 N (1.0 - 10 lb) 的力向下直压在桥的接触表面上。
- 顺时针旋转调节螺钉。 气门桥润滑油道中的油膜会向里移动。 油膜表明调整螺钉已接合气门杆。
- 将螺钉多转动 20° 至 35°(1/3 至 1/2 面)。 这样可矫直导杆中的定位销并补偿螺纹中的松弛。
- 将调整螺钉固定在该位置。 将锁紧螺母拧紧至扭矩 30 ± 4 N·m (22 ± 3 lb ft)。
Show/hide table
图 5 | g01422756 |
- 用工具 (A) 确保推杆 (1) 和摇臂上无压力。 用工具 (B) 将摇臂从推杆上拉开。 将推杆 (1) 安装在摇臂下方的位置。 如果无法充分移动摇臂来将推杆安装到位,则用工具 (A) 转动曲轴。
- 调整气门,以达到进口 0.38 ± 0.10 mm (0.015 ± 0.004 in)、出口1.02 ± 0.10 mm (0.04 ± 0.004 in) 的间隙。 请参阅测试和调整, "发动机气门间隙"。
End By: 安装变压器。
Caterpillar Information System:
CG137-08 and CG137-12 Engines Valve Cover Base - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Timing Gears - Remove and Install
CG137-08 and CG137-12 Engines Timing Gear Cover - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
C4.4 Marine Generator Set Before Starting Engine
C15 Engines for Combat and Tactical Vehicles Lubrication System
3516C Generator Sets Engine Crankcase Breather - Clean
3516C Generator Sets Glossary
C13, C15, and C18 Tier 4 Final Engines Front Housing and Covers
3516C Generator Set Engines Catalytic Converter Sensor
C13, C15, and C18 Tier 4 Final Engines Pressure Sensor (Exhaust Differential)
CG137-08 and CG137-12 Engines Cylinder Head - Remove and Install - G3412B
CG137-08 and CG137-12 Engines Pistons and Connecting Rods - Remove and Install
CG137-08 and CG137-12 Engines Cylinder Liner - Remove and Install
CG137-08 and CG137-12 Engines Camshaft - Remove and Install
371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 371-1079 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
CG137-08 and CG137-12 Engines Camshaft Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft Main Bearings - Remove and Install
CG137-08 and CG137-12 Engines Crankshaft - Remove and Install
TH55FT-E70 and TH55FT-E90 Transmissions Daily Inspection
CG137-08 and CG137-12 Generator Sets Turbocharger
C15 Engines for Combat and Tactical Vehicles Electronic Unit Injector - Adjust
Installation Procedure for Improved Jacket Water Heater on Certain C27 Generator Sets{1383} Installation Procedure for Improved Jacket Water Heater on Certain C27 Generator Sets{1383}