Air Inlet and Exhaust Lines
Show/hide table
图 1 | g02553656 |
右视图 |
Show/hide table
图 2 | g02553638 |
螺栓拧紧顺序 |
Show/hide table
技术规格 - 285-8373 空气管路总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 4 | 239-6808 卡箍 | 在装配前,使用 C5A 铜防咬合剂润滑螺纹、轴承表面和内径。 |
拧紧至扭矩为 |
|||
2 | 4 | 6V-5103 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
3 | 10 | 8J-5985 螺栓 | 采用以下步骤组装后冷器组件并拧紧螺栓:
1. 将密封组装到后冷器芯上。 2. 临时用胶带将底部密封固定在后冷器上。 不要使用粘接剂、硅润滑剂或任何其它润滑剂来固定密封。 3. 将装了密封的后冷器组装到进气歧管上。 4. 检查底部密封,以确保密封正确座入凹槽内。 5. 安装后冷器盖。 6. 检查顶部密封,以确保密封正确座入凹槽内。 7. 安装盖螺栓。 用手拧紧盖螺栓。 8. 按照图 2 中所示的数字顺序拧紧螺栓至扭矩 9. 按照图 2 中所示的数字顺序将螺栓再次拧紧至 10. 拆下胶带。 |
4 | 12 | 6V-5101 O 形密封圈 | 组装前,使用甘油或经认可的等同物质稍稍润滑孔。 |
Caterpillar Information System:
3500 Engines Air Inlet and Exhaust Lines
3500 Engines Air Inlet and Exhaust Lines
C15 Petroleum Engines Configuration Parameters
Procedure for Installing a Redesigned Jacket Water System on Certain C15 and C18 Generator Sets{1350, 1380, 1383} Procedure for Installing a Redesigned Jacket Water System on Certain C15 and C18 Generator Sets{1350, 1380, 1383}
CG137-08 and CG137-12 Engines Configuration Parameters
C175-16 Petroleum Generator Set Engines Air Prelube Pump Lubricator Bowl - Clean
XQ400 Power Module Control Panel
C15 Petroleum Engines Fan Drive
797F and 797F XQ Off-Highway Truck Hydraulic Fan System System Pressure - Release
C175-16 and C175-20 Generator Set Engines Fuel Injector
3500 Engines Air Inlet and Exhaust Lines
3500 Engines Air Inlet and Exhaust Lines
CG137-08 and CG137-12 Engines Safety Messages
C15 Petroleum Engine Electronic Control System Components
2011/05/11 Drain the Rubber Boot for the Hydraulic Actuators on G3500 and G3600 Engines {1057, 1265}
3500B and 3500C Marine Engines Air Shutoff
3500 Engines Air Shutoff
C15 and C18 Industrial Engines Flywheel
3500 Engines Air Shutoff
C13, C15, and C18 Tier 4 Final Engines Flywheel
C9.3 Tier 4 Final Engines Exhaust Diffuser Adapter
3500 Engines Air Shutoff
C13, C15, and C18 Tier 4 Final Engines Flywheel
C13, C15, and C18 Tier 4 Final Engines Flywheel