Engine Oil Sample - Obtain
除了要有良好的预防性维护程序之外,Caterpillar 还建议定期采用 S·O·S 机油分析,以监控发动机的状况和发动机的保养要求。 S·O·S 机油分析提供红外线分析,用以确定硝化和氧化程度。
Show/hide table
热油和热的部件可能会导致人员受伤。 不要让热的油和部件接触皮肤。 |
有关油样的更多信息,请参考 PEDP8025, "优化机油更换周期"。
在进行机油采样以前,先填写标签 , PEEP5031,以识别油样。 为了有助于获得最精确的分析结果,提供下列信息:
- 发动机型号
- 发动机的工作时数
- 上次更换机油以来的累计工作小时数
- 上次更换机油以来的机油添加量
Show/hide table
图 1 | g02049253 |
发动机正面机油取样阀视图 |
Caterpillar 建议使用取样阀来获取机油油样。 使用取样阀时,油样的油质和一致性较好。 取样阀的位置使得油样能在发动机正常运转时压力下流出。
为了确保油样能代表曲轴箱中的机油,要获取热的、充分混合的机油油样。
为了避免机油油样的污染,用来获取机油油样的工具和容器必须清洁。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关适于收集和盛放 Cat 产品油液的工具和用品,请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。 按照本地法规和要求处置所有油液。 |
用取样阀的情况下,建议使用 169-8373 油液取样瓶。 油液取样瓶包括取样所需要的零件, 同时还提供了说明。
Show/hide table
注意 |
---|
必须分别使用专用的机油采样泵和冷却液采样泵。 使用同一个泵去进行两种液体的采样会污染抽取的液样。 这种污染可能会导致代理商和客户关注由此造成错误的分析和不正确的解释。 |
有关说明请参考专门出版物 , PEGJ0047 , "如何获得良好的 S·O·S 油样"。 请咨询 Caterpillar 代理商以获得完整资料和协助制订您发动机的 S·O·S 程序。
Caterpillar Information System:
793F Off-Highway Truck Machine Systems Heater Coil - Remove and Install
793F Off-Highway Truck Machine Systems Evaporator Coil - Remove and Install
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Sound Information
CX31-P600 Petroleum Transmission Gear Pump (Transmission)
General Salvage and Reconditioning Techniques {0374, 1000} General Salvage and Reconditioning Techniques {0374, 1000}
Procedure to Install the 210-2540 Bellows As on Some 3512B Locomotive Engines{1052, 1053, 1061} Procedure to Install the 210-2540 Bellows As on Some 3512B Locomotive Engines{1052, 1053, 1061}
Installation and Configuration of the Network Management Card{4480} Installation and Configuration of the Network Management Card{4480}
793F Off-Highway Truck Machine Systems Foot Brake Control (Service) - Remove and Install
793F Off-Highway Truck Machine Systems Foot Brake Control (Secondary) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Exhaust Combustion Lines
793F Off-Highway Truck Machine Systems Electronic Control Module (VIMS Main Module) - Remove and Install
793F Off-Highway Truck Machine Systems Electronic Control Module (Integrated Brake) - Remove and Install
793F Off-Highway Truck Machine Systems Valve (Heater Control) - Remove and Install
793F Off-Highway Truck Machine Systems Engine Shutdown Switch and Disconnect Switch - Remove and Install
CX31-P600 Petroleum Transmission Power Train Electronic Control Module (Electronic Clutch Pressure Control)
349F and 352F Excavators Alternate Exit
C13-XQ350 Rental Generator Set Electronic Modular Control Panel 4 (EMCP 4)
C13 and C15 Engines for Combat and Tactical Vehicles 5 Volt Engine Pressure Sensor Supply Circuit - Test
C13 and C15 Engines for Combat and Tactical Vehicles Accelerator Pedal (Throttle) Position Sensor Circuit - Test
3508, 3512 and 3516 Generator Set Engines Camshaft - Install
C13, C15, and C18 Tier 4 Interim Engines Diagnostic Trouble Codes
C13, C15, and C18 Tier 4 Interim Engines Event Codes
C13, C15, and C18 Tier 4 Interim Engines Inlet Air Is Restricted
C6.6 Generator Set CID 0001 FMI 02