Coolant Temperature Sensor - Remove and Install
- Drain the coolant into a suitable container for storage or for disposal. Drain the coolant to a level that is below the coolant temperature sensor. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Show/hide table
Illustration 1 g01520324 - Disconnect harness assembly (2) from coolant temperature sensor (1).
- Remove coolant temperature sensor (1) from the engine.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Install the O-ring seal onto coolant temperature sensor (1).
- Install coolant temperature sensor (1) into the engine. Tighten coolant temperature sensor (1) to a torque of
20 ± 3 N·m (15 ± 2 lb ft) . - Connect harness assembly (2) onto coolant temperature sensor (1).
- Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Show/hide table
Illustration 2 | g01520324 |
Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
Caterpillar Information System:
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0110 - FMI 09
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0110 - FMI 04
2012/10/04 Procedure Now Available to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
Air Conditioning and Heating R134a for All Caterpillar Machines Heating and Air Conditioning Service Publications
Air Conditioning and Heating R134a for All Caterpillar Machines Air Conditioning System Troubleshooting
C7 PETROLEUM Petroleum Engine Atmospheric Pressure Sensor - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System Event Code List
C15 Petroleum Generator Set Engines Cylinder Head
2008/04/28 Improved Turbocharger {1052, 1053}
C6.6 Marine Generator Set Safety Messages
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498} Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Rebuilding Front Axles, Spindle Housings, Leaning Arms, and Lean Bars {4313, 5211, 5225} Rebuilding Front Axles, Spindle Housings, Leaning Arms, and Lean Bars {4313, 5211, 5225}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0190 - FMI 08
Air Conditioning and Heating R134a for All Caterpillar Machines Troubleshooting Heating and Air Conditioning Control System
C7 PETROLEUM Petroleum Engine Engine Oil Pressure Sensor - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0248 - FMI 12
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0262 - FMI 06
Air Conditioning and Heating R134a for All Caterpillar Machines In-Line Refrigerant Dryer - Remove and Install
Service Procedure for Improperly Flashed ECM's{1901, 1920, 7620} Service Procedure for Improperly Flashed ECM's{1901, 1920, 7620}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0291 - FMI 03
345D, 349D and 349D2 Excavators Hydraulic System Counterweight (Removal and Installation Hydraulic System)
2008/04/21 An Improved Bearing is Now Used in the Torque Converter for Certain Oil/Gas Transmissions {3101}
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Receiver-Dryer - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0291 - FMI 05