Vibration Damper and Pulley - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud 1/2 - 13 NC by 6 inch |
2 |
- Remove belt (3) from vibration damper (1).
- Remove two bolts (2) and install Tooling (A).
- Remove bolts (4).
Show/hide table
Illustration 2 g01366694 - Slide first vibration damper (1) forward. Attach a suitable lifting device onto first vibration damper (1). The weight of vibration damper (1) is approximately
34 kg (75 lb) . Remove first vibration damper (1) and the spacers from adapter (5). - Remove the pulley.
- Slide second vibration damper (1) forward. Attach a suitable lifting device onto second vibration damper (1). The weight of vibration damper (1) is approximately
34 kg (75 lb) . Remove second vibration damper (1) and the spacer from adapter (5). - Remove remaining bolts (2) and adapter (5).
Show/hide table
Illustration 1 | g01366691 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Stud 1/2 - 13 NC by 6inch |
2 |
- Install Tooling (A) in the crankshaft.
- Position adapter (5) on Tooling (A) and install the washers and bolts (2).
- Attach a suitable lifting device onto second vibration damper (1). The weight of vibration damper (1) is approximately
34 kg (75 lb) . Position the spacer and second vibration damper (1) on adapter (5). - Install the pulley.
- Attach a suitable lifting device onto first vibration damper (1). The weight of vibration damper (1) is approximately
34 kg (75 lb) . Position the spacers and first vibration damper (1) on adapter (5).Show/hide tableIllustration 4 g01366691 - Install bolts (4). Tighten bolts (4) to a torque of
135 ± 20 N·m (100 ± 15 lb ft) . - Remove Tooling (A) and install the two washers and bolts (2). Tighten bolts (2) to a torque of
215 ± 40 N·m (159 ± 30 lb ft) . - Install belt (3) on vibration damper (1).
Show/hide table
Illustration 3 | g01366694 |
Caterpillar Information System:
2009/02/02 A New Pushrod Is Now Used {1102, 1121, 1123}
3512B Marine Auxiliary Engine Overhaul (Top End)
2007/04/02 Make Sure That The Turbocharger Coolant Is Vented {1052}
C9 Agricultural Engine for Challenger Tractors Sensor Supply - Test
C18 Generator set and C18 Marine Engines Valve Mechanism Cover Base - Remove and Install
C9 Agricultural Engine for Challenger Tractors Acceleration Is Poor or Throttle Response Is Poor
C18 Generator set and C18 Marine Engines Housing (Front) - Install
C3.4 Engines for Caterpillar Built Machines Fuel Injection Pump
C9 Agricultural Engine for Challenger Tractors Event Code List
Procedure to Replace the Solenoid on the Electronic Actuator Group{1716} Procedure to Replace the Solenoid on the Electronic Actuator Group{1716}
C18 Generator set and C18 Marine Engines Housing (Front) - Remove
C9 On-highway Engine Exhaust Combustion Manifold - Remove and Install
C9 Agricultural Engine for Challenger Tractors Engine Misfires, Runs Rough or Is Unstable
2007/04/09 An Improved Clamp is Used {1355, 1380, 1393}
C18 Marine Auxiliary Engines Switch Circuits - Test
TA19 and TA22 Transmissions Power Train Electronic Control System Event Code List
C18 Marine Auxiliary Engines Indicator Lamp - Test
C32 Marine and Auxiliary Marine Engines Housing (Front) - Remove
3512B Marine Auxiliary Engine Safety Messages
Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064} Filtration Procedure for Oil in the Motor Grader Tandem Drive {0680, 0738, 0768, 4062, 4064}
C32 Petroleum Engines Belts - Inspect/Adjust/Replace
C32 Marine Engines Housing (Front) - Install
C18 Marine Auxiliary Engines Engine Top Speed Is Not Obtained
C15 and C18 Petrolem Generator Set Engines General Information