Tilt Cylinder
Show/hide table
 | |
| 图 1 | g01979962 |
(1) 活塞直径（单棱） ... 218.00 ± 0.13 mm (8.583 ± 0.005 in)
(2) 活塞直径（双棱） ... 219.00 ± 0.05 mm (8.622 ± 0.002 in)
(3) 活塞直径 ... 218.0 ± 0.5 mm (8.58 ± 0.02 in)
(4) 用少许密封的油液润滑密封唇。
(5) 组装前将 4C-9507 固定剂 涂在刮尘密封槽上。
(6) 螺母的扭矩 ... 13500 ± 1350 N·m (9950 ± 995 lb ft)
注: 安装螺母前，润滑油缸连杆的螺纹。
(7) 油缸连杆直径 ... 114.250 ± 0.038 mm (4.4980 ± 0.0015 in)
(8) 缸孔直径 ... 220.05 ± 0.10 mm (8.663 ± 0.004 in)
(9) 倾斜油缸缸盖孔径（双内棱） ... 115.30 ± 0.03 mm (4.539 ± 0.001 in)
(10) 油缸缸盖孔径（双外棱） ... 114.58 ± 0.03 mm (4.511 ± 0.001 in)
(11) 螺栓的扭矩 ... 900 ± 100 N·m (665 ± 75 lb ft)
231-1955 倾斜油缸总成
销与销之间的闭合长度 ... 2665 mm (104.9 in)
油缸冲程 ... 1770 mm (69.70 in)
271-6441 倾斜油缸总成
销与销之间的闭合长度 ... 2481 mm (97.7 in)
油缸冲程 ... 1621 mm (63.82 in)
Caterpillar Information System:
Product Link - PL102C System Schematic
988H Wheel Loader Electrohydraulic System Ride Control Accumulator
988H Wheel Loader Electrohydraulic System Ride Control Valve
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader Low Power/Poor or No Response to Throttle
Bench Test Procedure for a 637E and 637G Wheel Scraper Transmission{3030, 3066, 3073, 3101} Bench Test Procedure for a 637E and 637G Wheel Scraper Transmission{3030, 3066, 3073, 3101}
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0623 - FMI 04
992K Wheel Loader Electrohydraulic System Solenoid Valve (Hydraulic Lockout)
D11R Track-Type Tractor Hydraulic System Return Screen - Clean
988H Wheel Loader Electrohydraulic System Pilot Control Actuator
2004/06/07 Certain Components of the Draft Frame Assembly Are Now Serviced {6207, 6245}
2004/05/03 A New Type of Main Bearing is Available {1202, 1203}
988H Wheel Loader Electrohydraulic System Piston Motor (Hydraulic Fan)
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0626 - FMI 03
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0626 - FMI 04
Bench Test Procedure for a 938H and 938G Series 2 Wheel Loader and IT38H and IT38G Series 2 Integrated Toolcarrier Transmission{3030, 3073} Bench Test Procedure for a 938H and 938G Series 2 Wheel Loader and IT38H and IT38G Series 2 Integrated Toolcarrier Transmission{3030, 3073}
988H Wheel Loader Electrohydraulic System Lift Cylinder
994F Wheel Loader Fast Fill Service Center
Product Link - PL102C Configuration
988H Wheel Loader Electrohydraulic System Position Sensor (Lift Linkage, Tilt Linkage)
994D Wheel Loader Air Dryer Desiccant - Replace
988H Wheel Loader Electrohydraulic System Bucket Control (Pins and Bearings)
988H Wheel Loader, 834H Wheel Dozer and 836H Landfill Compactor Machine Systems Governor Pedal
Product Link - PL102C Diagnostic Capabilities
D9T Track-Type Tractor Machine Systems Steering Motor - Disassemble