Ejector - Calibrate
Show/hide table
图 1 | g00926684 |
卡特彼勒电子技师软件配备变速箱/底盘系统标定特性。 将 ET 与车辆相连即可进入标定模式。 选择变速箱/底盘 ECM。 如图 1 中所示。
Show/hide table
图 2 | g00926856 |
在选择变速箱/底盘 ECM 后,通过"维修菜单 (Service Menu)"即可进入标定步骤。 从菜单中选择"标定 (Calibrations)"。 如图 2 中所示。
Show/hide table
图 3 | g00749496 |
ET 屏幕上会显示标定过程中的安全警告。 阅读完警告后选择"确定 (OK)"。
电液控制阀的标定决定着所有机具功能使用的液压油开始流动的时刻。 标定决定着启动油缸流量时必须送至各个阀的电流量。 确定建立油缸全流所需的电流量。 变速箱/底盘 ECM 会在存储器中记录这些电流。 在更换 ECM 或重新进行标定步骤之前 ECM 一直使用这些范围值。
在第一次进行阀的标定时,必须进行本步骤的所有部分: 铲运斗, 挡板 和 推土器. 在后继的重新标定过程中,可以单独进行本步骤的各个部分。
- 选择正确的标定。 选择需要的选择框。 见图 4。 要标定推土器电磁阀,选择"推土器电磁阀标定 (Ejector Solenoids Calibration)" (2) 。
Show/hide table
图 4 | g00749483 |
(1) "铲运斗电磁阀标定" (2) "推土器电磁阀标定" (3) (挡板电磁阀标定) |
- ET 屏幕将指导技师在位置 (4) 和 (5) 处进行操作。 实际的指导如下所示:
Show/hide table
图 5 | g00929159 |
- 必须设置车辆停车制动器。
- 在机具油泵测压孔上连接 198-1758 电液标定维修工具组件 。 在变速箱电气线束中插入工具端。
Show/hide table
图 6 | g00749017 |
198-1758 电液标定维修工具组件 |
Show/hide table
图 7 | g01243371 |
图示为机器右侧 - 机型 627G 机具油泵测压孔的位置 (机型 621G、 623G、 631G 和 637G 的典型示图) |
Show/hide table
图 8 | g01243391 |
图 7 的近视图 - 机型 627G 机具油泵压孔的位置 (机型 621G、 623G、 631G 和 637G 的典型示图) |
Show/hide table
图 9 | g01243438 |
图示为机型 657G 油泵测压孔的位置(从牵引机左侧挡泥板后部观察)。 |
Show/hide table
图 10 | g01243450 |
图 9 的近视图 - 机型 657G 油泵测压孔的位置。 |
- 起动发动机并在高怠速下运转。
- 运转机器,使液压油温度在 50 °C (122 °F) 至 75 °C (167 °F)。
- 铲运斗必须完全清空物料。
- 将推土器移到完全前移位置。
- 在满足先前的初始条件后,选择 ET 中的"下一步 (NEXT)"按钮。
- 将操纵手柄移到推土器完全前移位置。 保持操纵手柄,直到 ET 软件显示标定完成为止。
- 松开操纵手柄。
- 将推土器移至完全后移位置。
- 在满足先前的初始条件后,选择 ET 屏幕上的"下一步 (NEXT)"按钮。
- 将操纵手柄移到推土器完全后移位置。 在该位置保持操纵手柄,直到 ET 软件显示标定完成为止。
- 松开操纵手柄。
- ET 软件随后会显示一个表明标定状态的屏幕。
Show/hide table
图 11 | g00929152 |
- 此时,如果不需要标定其它阀,即可退出标定过程。 也可以继续标定其它阀。
注: 如果没有在 5 分钟内完成标定或标定失败,确保操纵手柄在正确的位置。 不可以标定操纵手柄。 如果标定总是失败,请参阅故障诊断, "电磁阀标定不成功"。
Caterpillar Information System:
621G, 623G and 627G Wheel Tractor-Scrapers Air System and Brakes Brake Actuator
AD55 Underground Articulated Truck Sound Information and Vibration Information
2002/11/04 Correction to the Operation and Maintenance Manual, "Wheel Bearings - Check/Adjust" {4050}
AD55 Underground Articulated Truck Power Train Pressure Control Valve (Transmission)
AD55 Underground Articulated Truck Parking
D6N Track-Type Tractor Operation Information
D5N Track-Type Tractor Specifications
621G Wheel Tractor-Scraper Engine Starting with Auxiliary Start Receptacle
3516B Engine for Caterpillar Built Machines Electronic Display Module
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Bowl - Calibrate
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Apron Control (Joystick) - Calibrate
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Ejector Control (Joystick) - Calibrate
621G Wheel Tractor-Scraper Braking System - Test
651E and 657E Wheel Tractor-Scrapers Hydraulic System Accumulator (Cushion-Hitch)
621G, 623G and 627G Wheel Tractor-Scrapers Air System and Brakes Service Brake
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Apron - Calibrate
637G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect/Replace
637G Wheel Tractor-Scraper Engine Crankcase Breather - Clean
637G Wheel Tractor-Scraper Engine Oil (High Speed) and Oil Filter - Change
2002/10/07 Correction to Specifications , "Draft Frame" {6207}
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System General Information
623G Wheel Tractor-Scraper Safety Messages
637G Wheel Tractor-Scraper Engine Oil Level - Check
637G Wheel Tractor-Scraper Engine Oil Sample - Obtain