170-9227 Reamer Shims Will Control Injector Sleeve Reaming {0700, 0703, 0706, 1000}
- Engine: Commercial with Mechanical Unit Injection
- 3126
- Engine: Commercial with Mechanical Unit Injection
- 3116
- 3126
Features/Benefits
The reamer shims are used to control depth of the injector sleeve reaming operation. The reamer sleeves will allow only 0.25 mm (.010 inch) of material to be removed during each reaming. The reamer shims prevent the sleeve from being too deeply reamed. Reamer shims provide a positive stop at the end of each reaming operation. The shims minimize reamer vibration.
Procedure
- Install four shims between the Reamer Shanks and the bushing.
- The sleeve is reamed until the reamer shank contacts the shim.
- One shim at a time should be removed until proper depth is obtained.
Specifications/Technical Information
Show/hide table
Illustration 1 | g00702594 |
(1) 170-9227 Reamer Shims (2) 4C-8713 Reamer Shank (3) 4C-8714 Bushing |
Thickness ... 0.25 mm (.010 inch)
Number of shims per packet ... 4
Reference
Refer to Tool Operating Manual, NEHS0675, "Using the 143-2099 Sleeve Replacement Tool Group ".Caterpillar Information System:
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel System
797 Off-Highway Truck Fan Drive Hydraulic System Speed Sensor (Fan Drive)
3500B High Displacement Locomotive Engines Override Switch (Engine Monitoring System)
G3516B Engines E403 Cylinder #3 Detonation
G3516B Engines E402 Cylinder #2 Detonation
3126B and 3126E On-highway Engines Engine Misfires, Runs Rough or Is Unstable
3500B High Displacement Engines Engine Speed/Timing Sensor
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 04 Atmospheric Pressure short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 04 Turbo Outlet Pressure short to ground
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
3500B Direct Fuel Control Modification (Hardware Version II){1250, 1901} 3500B Direct Fuel Control Modification (Hardware Version II){1250, 1901}
G3516B Engines E404 Cylinder #4 Detonation
G3516B Engines E405 Cylinder #5 Detonation
G3516B Engines E406 Cylinder #6 Detonation
G3516B Engines E407 Cylinder #7 Detonation
G3516B Engines E408 Cylinder #8 Detonation
G3516B Engines E409 Cylinder #9 Detonation
G3516B Engines E410 Cylinder #10 Detonation
G3516B Engines E411 Cylinder #11 Detonation
G3516B Engines E412 Cylinder #12 Detonation
G3516B Engines E413 Cylinder #13 Detonation
G3516B Engines E414 Cylinder #14 Detonation
G3516B Engines E415 Cylinder #15 Detonation