Swivel - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-2674 | Vacuum Cap | 1 |
| B | 138-7575 | Link Bracket | 2 |
Start By:
- Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply
276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.Show/hide table
Illustration 2 g01285340 - Disconnect hose assemblies (1), (2), (3), (4), (5) and (6). Remove support (7).
Show/hide table
Illustration 3 g01285376 - Attach Tooling (B) and a suitable lifting device to swivel (12) . The weight of swivel (12) is approximately
45 kg (100 lb) . Remove bolts (9) and retainer (11). Remove clamp (10) and boot (8).Show/hide table
Illustration 4 g01285383 Show/hide table
Illustration 5 g01285339 - Slowly remove bolts (14). Allow cover (13) to lower. Remove bolts (14) and rotate cover (13) out of the way.
Show/hide table
Illustration 6 g01285390 - Disconnect hose assemblies (18). Disconnect fitting (19). Disconnect hose assemblies (15). Remove fittings (17). Remove bolts (16). Remove swivel (12).
Show/hide table
| |
| Illustration 1 | g01209599 |
Caterpillar Information System:
318B Excavator Machine System Specifications Bucket Cylinder
330D Forest Machine Hydraulic System Relief Valve (Line) - Test and Adjust
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting - Guide for Actuators
3176C Engines for Caterpillar Built Machines Digital Sensor Supply Circuit - Test
330D Forest Machine Hydraulic System Relief Valve (Main) - Test and Adjust - Heavy Lift
330D Forest Machine Hydraulic System Cylinder Speed - Check
C15 Petroleum Generator Set Engines Valve Mechanism
2006/08/14 Improved Window Latches are Now Used {7310}
324D and 325D Forest Machines Machine Systems Swing Cushion Valve - Assemble
H35D S, H45D S, H55D S and H65D S Hydraulic Hammers Hammer Hydraulic System
324D and 325D Forest Machines Machine Systems Swing Cushion Valve - Disassemble
2006/11/20 The Seal for the Hydraulic Filter Is Improved and a Modified Plate Improves the Breathing of the Hydraulic Tank {5056, 5068}
3176C Engines for Caterpillar Built Machines CID 0296 FMI 09 Unable to communicate with Transmission ECM
324D and 325D Forest Machines Machine Systems Swivel - Install
325D Material Handler Capacities (Refill)
3176C Engines for Caterpillar Built Machines CID 1599 FMI 05 Engine Fan Pull Solenoid open circuit
3176C Engines for Caterpillar Built Machines CID 1599 FMI 06 Engine Fan Pull Solenoid short to ground
390D Excavator Machine Systems Final Drive - Assemble
3176C Engines for Caterpillar Built Machines CID 1600 FMI 06 Engine Fan Push Solenoid short to ground
3176C Engines for Caterpillar Built Machines CID 1600 FMI 05 Engine Fan Push Solenoid open circuit
3176C Engines for Caterpillar Built Machines CID 0545 FMI 06 Ether Start Relay short to ground
3176C Engines for Caterpillar Built Machines CID 0545 FMI 05 Ether Start Relay open/short to +batt
324D and 325D Forest Machines Machine Systems Swing Motor - Remove
330D Forest Machine Hydraulic System Relief Valve (Swing) - Test and Adjust