Engine Oil Cooler - Remove
Start By:
- Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter Base - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the oil from the engine oil cooler into a suitable container for storage. Drain the coolant from the cooling system. Refer to Operation and maintenance Manual, "Cooling System Coolant (Deac) - Change" in order to drain the coolant.
Show/hide table
Illustration 1 g00619340 Typical example - Remove bolts (1) that hold oil cooler bonnet (2) to the engine.
- Remove bolts (4) that hold the oil cooler bonnet (5) to the water pump.
- Use two technicians to remove oil cooler (3), oil cooler bonnet (2), and oil cooler bonnet (5) as an assembly. The weight of oil cooler (3), oil cooler bonnet (6), and oil cooler bonnet (5) is approximately
24 kg (53 lb) . - Remove the gaskets from oil cooler bonnet (2) and from oil cooler bonnet (5).
Caterpillar Information System:
3406E and 3456 Generator Set Engines Fuel Filter Base - Remove
3512B Marine Auxiliary Engine MID 047 - CID 1361 - FMI 04 DFW Gen Oil Cooler Inlet Temp Sensor short to gnd
3512B Marine Auxiliary Engine MID 047 - CID 1361 - FMI 03 DFW Gen Oil Cool In Temp Sens open/short to +batt
3512B Marine Auxiliary Engine MID 047 - CID 1360 - FMI 04 DFW Gen Oil Cooler Outlet Temp Sensor short to gnd
3512B Marine Auxiliary Engine MID 047 - CID 1360 - FMI 03 DFW Gen Oil Cool Out Temp Sens open/short to +batt
C-15, C-16 and C-18 Truck Engines Accessory Drive - Remove
3512B Marine Auxiliary Engine MID 047 - CID 1359 - FMI 04 DLO Gen Cooler Outlet Temp Sensor short to gnd
3512B Marine Auxiliary Engine MID 047 - CID 1359 - FMI 03 DLO Gen Cooler Out Temp Sensor open/short to +batt
P16, P20, P25, P28, P40 and P60 Pulverizers Ring Gear - Remove and Install
3512B Marine Auxiliary Engine MID 047 - CID 1358 - FMI 04 DLO Gen Cooler Inlet Temp Sensor short to gnd
3512B Marine Auxiliary Engine MID 047 - CID 1358 - FMI 03 DLO Gen Cool Inlet Temp Sensor open/short to +batt
3512B Marine Auxiliary Engine MID 047 - CID 1352 - FMI 04 DFW Aftercooler Outlet Temp Sensor short to gnd
3512B Marine Auxiliary Engine MID 036 - CID 1365 - FMI 05 Black Start Push Button Lamp open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1201 - FMI 05 Thermocouple #1 open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1201 - FMI 04 Thermocouple #1 short to ground
3512B Marine Auxiliary Engine MID 111 - CID 1202 - FMI 04 Thermocouple #2 short to ground
3512B Marine Auxiliary Engine MID 111 - CID 1202 - FMI 05 Thermocouple #2 open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1203 - FMI 04 Thermocouple #3 short to ground
3126B and 3126E On-highway Engines Belt Tightener - Remove
3512B Marine Auxiliary Engine MID 111 - CID 1203 - FMI 05 Thermocouple #3 open circuit
3500B Engines Turbocharger - Remove - Rear Mounted Turbocharger
3512B Marine Auxiliary Engine MID 111 - CID 1204 - FMI 04 Thermocouple #4 short to ground
3512B Marine Auxiliary Engine MID 111 - CID 1204 - FMI 05 Thermocouple #4 open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1205 - FMI 04 Thermocouple #5 short to ground