Fan Drive - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-0510     | Driver Group     | 1     |
B     | 1P-0808     | Multipurpose Grease     | -     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install bearing (4) in pulley (5) .
Show/hide table
Illustration 1 | g01029786 |
- Install lip seal (3) with Tooling (A), as shown. Apply Tooling (B) to the lip of the seal.
- Install spacer (2) so the end with the taper is toward the inside of pulley (5) .
- Install spacer (6) and bearing (9) in the front of pulley (5) .
- Position O-ring seal (7) on the front of pulley (5). Install the pulley on shaft assembly (1) .
- Install retainer (10) and bolts (11). Tighten bolts (11) to a torque of 25 ± 6 N·m (18 ± 4 lb ft).
- Install the fan adapter on pulley (5). Tighten bolts (8) to a torque of 47 ± 9 N·m (35 ± 7 lb ft).
- Fill the fan drive with Tooling (B) .
End By: Install the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Install".
Caterpillar Information System:
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0808 FMI 09 Interface Module (No. 8) Abnormal Update - Test
3304B and 3306B Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0807 FMI 09 Interface Module (No. 7) Abnormal Update - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0806 FMI 09 Interface Module (No. 6) Abnormal Update - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0805 FMI 09 Interface Module (No. 5) Abnormal Update - Test
3406E On-Highway Engine Fan Drive - Disassemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0804 FMI 09 Interface Module (No. 4) Abnormal Update - Test
Optimizing Machine Performance Over the Lifetime of the M318 Excavator{1900, 5051, 5137, 5479, 5480} Optimizing Machine Performance Over the Lifetime of the M318 Excavator{1900, 5051, 5137, 5479, 5480}
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Hydraulic System Pressure - Release
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Visual Inspection
302.5 Mini Hydraulic Excavator Specifications
3524B Engines for Off-Highway Trucks Too Much Valve Lash
3406E On-Highway Engine Fan Drive - Remove
3406E and 3456 Generator Set Engines Fan Drive - Install
302.5 Mini Hydraulic Excavator Plate Locations and Film Locations
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Hydraulic Oil Contamination - Test
302.5 Mini Hydraulic Excavator Travel Alarm - If Equipped
302.5 Mini Hydraulic Excavator Heating Control
320B Excavator Hydraulic System Pump Control (Output Flow) - Adjust
A13 Auger Lifting and Tying Down the Work Tool
A13 Auger Transport Position
3406E On-Highway Engine Coolant Temperature Sensor - Remove and Install
302.5 Mini Hydraulic Excavator Travel Speed Control
3046 Engine For Caterpillar Built Machines Fuel Injection Lines - Remove and Install