Flywheel - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | FT-0120     | 提升支架     | 1     |
开始:
- 拆卸电起动马达。 请参考解体与组装, "电起动马达 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 安装到飞轮上,并固定好起重机。
Show/hide table
图 1 | g00496720 |
- 从曲轴上拆下螺栓 (1) 和飞轮 (2) 。 飞轮的重量为 72 kg (160 lb)。
- 为了能将齿圈从飞轮上拆下,如果必要,可以使用锤子和冲头。
按照以下拆卸步骤拆卸不能固定到 FT0120 提升支架 上的飞轮。
Show/hide table
图 2 | g00599442 |
- 拆下八根螺栓 (1) 。
注: 通过将一根螺栓留在飞轮顶部来将飞轮固定到发动机缸体上。 为了便于安装,标记出飞轮和曲轴位置。
- 安装两个 5/8 in x 18 NF 螺栓。
Show/hide table
图 3 | g00599475 |
- 拆卸螺栓 (3) 。
- 使飞轮 (4) 滑出飞轮壳,滑到螺栓 (2) 上。
- 将皮带和适当的举升设备固定到飞轮 (4) 上。
Show/hide table
图 4 | g00599476 |
- 从发动机上拆下螺栓 (2) 和飞轮 (4) 。 飞轮的重量为 54 kg (120 lb)。
Caterpillar Information System:
3500B Engines Fuel Filter Housing - Assemble - Spin-on Filters
Converting a Four Cylinder Air Compressor Air Supply From a Pressurized Air Supply to a Naturally Aspirated Air Supply{1803} Converting a Four Cylinder Air Compressor Air Supply From a Pressurized Air Supply to a Naturally Aspirated Air Supply{1803}
3500B Engines and 3500 Engines with EUI Option Engine Sensor Open/Short Test
3500B and 3500B High Displacement Generator Set Engines Injector Solenoids
G3612 and G3616 Engines Air Lubricator - Remove and Install
3500B Engines Fuel Filter Housing - Disassemble - Spin-on Filters
3114, 3116 and 3126 Engines Coolant Temperature Above Normal
3500B Engines Fuel Filter Housing - Remove
3114, 3116 and 3126 Engines Coolant in Engine Oil
3114, 3116 and 3126 Engines Alternator Will Not Charge
G3612 and G3616 Engines Mounting Isolator - Remove and Install
3114, 3116 and 3126 Engines Alternator Charge Rate Is Low
G3612 and G3616 Engines Air Silencer - Remove and Install
3034 Engine for Caterpillar Built Machines Fuel Injection Pump - Remove
3500B Engines Fuel Filter Housing - Install - Spin-on Filters
3500B Engines Fuel Filter Housing - Install
G3612 and G3616 Engines Air Starting Motor - Remove
3500B Engines Fuel Priming Pump - Remove and Install
3500B Engines Fuel Transfer Pump - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fan Drive
3500B Engines Fuel Transfer Pump - Disassemble
G3612 and G3616 Engines Air Starting Motor - Install
G3408 and G3412 Engines Flywheel Housing
3114, 3116 and 3126 Engines Coolant Temperature Below Normal