Engine Oil Filter Housing - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将 O 形密封圈安装到壳体上。 安装盖 (23) 和螺栓 (22)。
- 安装 O 形密封圈 (25)。
- 必要时,安装销 (24)。 销必须高出壳体表面
6.50 ± 1.00 mm (0.256 ± 0.040 in) 。Show/hide table图 2 g00591546 - 安装旁通阀 (18) 和弹簧 (19)。
- 安装 O 形密封圈 (20) 和 (21)。
Show/hide table
图 3 g00591545 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装盖 (15) 和 (17)。 安装螺栓 (14) 和 (16)。
Show/hide table
图 4 g00591544 - 安装支架 (13)、螺栓和螺母 (12)。 将螺母上紧到
55 ± 7 N·m (41 ± 5 lb ft) 的扭矩。Show/hide table图 5 g00591541 - 安装 O 型密封圈 (11)。
- 必要时,将新销 (10) 装入旁通阀壳体中。 销必须高出壳体表面
6.50 ± 1.00 mm (0.256 ± 0.040 in) 。Show/hide table图 6 g00591504 - 安装过渡接头 (8)。 将 O 形密封圈 (9) 安装到过渡接头 (8) 上,并利用干净的机油润滑密封。
Show/hide table
图 7 g00591502 - 安装旁通阀壳体 (6)。 旁通阀壳体 (6) 的重量约为
43 kg (95 lb) 。 拧紧螺栓至扭矩为55 ± 7 N·m (41 ± 5 lb ft) 。 - 安装 O 形密封圈 (7)。
Show/hide table
图 8 g00591500 - 安装新机油滤芯 (5)。
Show/hide table
图 9 g00591498 - 将 O 形密封圈 (4)、弹簧 (3) 和护圈 (2) 安装到盖 (1) 上。
Show/hide table
图 10 g00591497 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 安装盖 (1) 和螺栓。
Show/hide table
图 1 | g00591547 |
结束:
- 安装发动机机油滤清器壳体。 参考拆解和组装, "发动机机油滤清器壳体 - 安装"。
Caterpillar Information System:
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0101 - FMI 04 Crankcase Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0101 - FMI 03 Crankcase Pressure open/short to +batt
G3500 Engines Engine Oil Filter Housing - Install
3406E and 3456 Generator Set Engines Electronic Control System Components
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0016 - FMI 05 Injector Cylinder 16 open circuit
3500B and 3500B High Displacement Generator Set Engines Engine Design
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0016 - FMI 06 Injector Cylinder 16 short
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0015 - FMI 05 Injector Cylinder 15 open circuit
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0015 - FMI 06 Injector Cylinder 15 short
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0014 - FMI 06 Injector Cylinder 14 short
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0014 - FMI 05 Injector Cylinder 14 open circuit
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0013 - FMI 06 Injector Cylinder 13 short
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Cylinder Block
G3500 Engines Engine Oil Cooler - Remove
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0262 - FMI 04 5 Volt Sensor DC Power Supply short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0262 - FMI 03 5 Volt Sensor DC Power Supply short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 03 Digital Sensor Supply short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 04 Digital Sensor Supply short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 04 Atmospheric Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 13 Atmospheric Pressure calibration required
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
3406E and 3456 Generator Set Engines Front Cover - Remove