Exhaust System Contains Fuel
- Short circuit in the ARD fuel pump relay wiring
- Corrosion in the wiring harness connectors for the ARD fuel pump relay
- Failed ARD fuel pump relay
Show/hide table
Illustration 1 | g06143030 |
ARD fuel pump schematic |
Complete the procedure in the order in which the steps are listed.
Carefully following this procedure is a good way to identify wiring problems.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Inspect the Components A. Visually inspect the components for the ARD fuel pump system. Look for the following problems: 1. Loose connections or damaged connectors 2. Moisture on the connectors or the wiring 3. Damage that is caused by excessive heat 4. Damage that is caused by chafing 5. Improper routing of wiring 6. Damaged insulation |
Damaged Wiring or Connectors |
Result: There is a problem with the wiring or a connector. Repair: Repair the wiring or connector. Replace parts, if necessary. Proceed to Test Step 4. Result: The wiring is OK. Proceed to Test Step 2. |
2. Check for Voltage at the Coil for the ARD Fuel Pump Relay A. Turn the keyswitch to the OFF position. B. Measure voltage between the relay coil and a good ground source. There should not be voltage on the relay coil when the keyswitch is in the OFF position. Low amounts of voltage can keep the relay pulled in after the keyswitch has been turned to the OFF position. |
Voltage |
Result: There is voltage between the relay coil and a good ground source. There may be a short from a power source in the wiring harness. There may be moisture or corrosion in a connector between the ECM and ARD fuel pump relay coil. Make the necessary repairs. Proceed to Test Step 4. Result: There is not voltage between the relay coil and a good ground source. Proceed to Test Step 3. |
3. Check for Voltage at the Load Side of the ARD Fuel Pump Relay A. Turn the keyswitch to the OFF position. B. Measure voltage between the load side of the ARD fuel pump relay and a good ground source. |
Voltage |
Result: There is voltage between the load side of the ARD fuel pump relay and a good ground source. Remove the relay. Check for voltage between the load side of the ARD fuel pump relay and a good ground source. If voltage is present, there is a short in the wiring between the relay and the ARD fuel pump. Repair or replace the wiring. If voltage is not present, the relay has failed. Repair: Replace the relay. Proceed to Test Step 4. Result: There is not voltage between the load side of the ARD fuel pump relay and a good ground source. For further assistance, confer with the Dealer Solutions Network (DSN). |
4. Clean Fuel from the Exhaust System A. Remove excess fuel from the piping with a clean cloth. B. Inhibit regeneration with the inhibit switch. C. Operate the engine at elevated idle (1500 RPM) for 20 minutes. |
Excess Fuel |
Result: The excess fuel and white smoke did not return after operating the engine for 20 minutes. Repair: Perform a Manual DPF Regeneration using the electronic service tool. Return the unit to service. Result: The excess fuel and white smoke returned after operating the engine for 20 minutes. Contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
C7.1 Engines and Generator Sets Exhaust System Contains Coolant
CB7, CB8 and CB10 Vibratory Asphalt Compactors Power Train Drum Mounting
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
994K Wheel Loader Machine Systems Seat - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Pilot Pressure - Test and Adjust
A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802} A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802}
Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304} Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304}
Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065} Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065}
2570D and 2670D Wheel Feller Buncher Engine Supplement Fan - Remove and Install
A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282} A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282}
Installation of the 519-9196 Lines Gp - Coupler on Certain Backhoe Loaders {5057, 5133, 6129} Installation of the 519-9196 Lines Gp - Coupler on Certain Backhoe Loaders {5057, 5133, 6129}
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil Filter Housing - Remove and Install
980L Tier 3 Wheel Loader Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Oil
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380} Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380}
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
MH3037 Material Handler Machine Systems Main Control Valve - Remove and Install - Lower Valve
C7.1 Engines and Generator Sets Fuel Contains Water
2570D and 2670D Wheel Feller Buncher Engine Supplement Piston Motor (Fan) - Remove and Install
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
C7.1 Engines and Generator Sets Fuel Temperature Is High
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble
C7.1 Engines and Generator Sets Inlet Air Is Restricted