TA2 Inspection for C4.4 Industrial Engine{0372, 1000, 7000, 753T, 7565}
- Industrial Engine:
- C4.4 (S/N: JKT1-UP)
Introduction
Inspections are the most basic form of condition monitoring. They are easy to do and surprisingly effective at helping you spot equipment health issues. Proactive monitoring and analysis of equipment information will allow Dealers to effectively intervene before problems occur.
Note: Before adjusting product settings to comply with listed baseline TA2 values, consult SIS for the latest specification values.
Creating an Electronic Copy
Use the following procedure to create an editable electronic copy from SIS Web.
- Click format to print.
- Save the document as an HTML format.
- Open the document with Microsoft Word.
Electrical System
Show/hide table
Status (1)     | Description     | Specification     | Actual     | Comments     |
---|---|---|---|---|
    | Inspect Battery Cables     | Cables between the battery, the starter, and the engine ground must be the correct size. Wires and cables must be free of corrosion. Wires and cables must have cable support clamps in order to prevent stress on battery connections (terminals).     |     |     |
    | Battery Test     | 12.4 VDC or more     |     | Refer to Special Instruction, SEHS7633, "Battery Test Procedure".     |
    | Charging System Test     |     |     | Refer to Systems Operation Testing and Adjusting, UENR4487, "Charging System -Test". Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".     |
    | Electric Starting System Test     |     |     | Refer to Systems Operation Testing and Adjusting, UENR4487, "Charging System -Test". Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
Engine
Cooling System
Show/hide table
Status (1)     | Description     | Specification     | Actual     | Comments     |
---|---|---|---|---|
    | Radiator Pressure Relief (Radiator Cap) (2)     |     |     |     |
    | Freezing Point of Engine Coolant     |     |     |     |
    | Conditioner Test of Engine Coolant     |     |     |     |
    | Difference between the Upper and Lower Radiator Tank Temperatures     |     |     |     |
    | Jacket Water Outlet Temperature     |     |     |     |
    | Aftercooler Water Outlet Temperature     |     |     |     |
    | Jacket Water Inlet Temperature from Cooling System     |     |     |     |
    | Oil Cooler Water Outlet Temperature     |     |     |     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
( 2 ) | Test for the pressure that is listed on the cap. |
Fuel System
Show/hide table
Status (1)     | Description     | Specification     | Actual     | Comments     |
---|---|---|---|---|
    | Fuel Pressure of the Low Pressure Fuel System at Idle Speed     | 150 kPa (22 psi)     |     |     |
    | Maximum Fuel Pressure of the High Pressure Fuel System     | 200 MPa (29000 psi)     |
    |     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
Lubrication System
Show/hide table
Status (1)     | Description     | Specification     | Actual     | Comments     |
---|---|---|---|---|
    | Minimum Engine Oil Pressure at Maximum Engine Speed     | 280 kPa (40 psi)     |
    |     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
Basic Engine
Show/hide table
Status (1)     | Description     | Specification     | Actual     | Comments     |
---|---|---|---|---|
    | Engine Speed at Low Idle     |     |     |     |
    | Engine Speed at High Idle     |     |     |     |
    | Cylinder Cutout Test     |     |     | Cat® Electronic Technician (Cat ET) Service Tool     |
    | Engine Crankcase Pressure (Blowby)     |     |     |     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
Air Inlet and Exhaust System
Show/hide table
Status (1)     | Description     | Specification     | Actual     | Comments     |
---|---|---|---|---|
    | Cylinder # 1 Exhaust Temperature (2)     |     |     |     |
    | Cylinder # 2 Exhaust Temperature (2)     |     |     |     |
    | Cylinder # 3 Exhaust Temperature (2)     |     |     |     |
    | Cylinder # 4 Exhaust Temperature (2)     |     |     |     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
( 2 ) | Compare the exhaust temperature variance at each exhaust port. |
S.O.S
Show/hide table
Status (1)     | Description     | Obtain     | Comments     | |
    | Engine Oil Sample     |     |     | |
    | Engine Coolant Sample (Level II)     |     |     | |
    | Hydraulic Oil Sample     |     |     |
Show/hide table
( 1 ) | N = Normal, M = Monitor, A = Action |
Caterpillar Information System:
C3.4B Engines DEF Pump Pressure Sensor - Test
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Lift Cylinder
R1600H Load Haul Dump Fuel System Primary Filter (Water Separator) - Replace
R1600H Load Haul Dump Fuel System Primary Filter (Water Separator) - Drain
2015/02/02 Improved Pressure Sensor Gp Is Now Used on Certain Cat® Products {1439}
785G Off-Highway Truck Systems Solenoid Valve Actuator
735C and 745C Articulated Trucks Torque Converter, Transmission, and Transfer Gear Oil Filter - Replace
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control Support
CW34 Pneumatic Compactor Engine Supplement Refrigerant Compressor - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Radiator, Hydraulic Oil Cooler, Air Cooler, and Fuel Cooler - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Primary Fuel Filter, Water Separator and Base - Remove and Install
CW34 Pneumatic Compactor Engine Supplement Muffler - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Bevel Gear and Pinion
C4.4 Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install
C4.4 Engines for Caterpillar Built Machines DEF Injector and Mounting - Remove and Install
C4.4 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Lines - Remove and Install
C4.4 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C4.4 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Tank - Remove and Install
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Lines (Diagnostic)
AP500F Asphalt Paver DEF Manifold Filters - Replace
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Load Control Valve Lines
C3.4B Engines Idle Validation - Test
525D, 535D, 545D and 555D Wheel Skidders Machine Systems Transmission Oil Pump
M318F, M320F and M322F Wheeled Excavators Machine System Specifications Valve and Lines