Machine Frame and Mounting
Show/hide table
Illustration 1 | g02771037 |
Show/hide table
Specifications for 345-5575 Loader Frame Gp     | |||
---|---|---|---|
Item     | Qty     | Part     | Specification Description     |
1     | -     | 8T-9022 Silicone Gasket     | Before assembling the 261-6101 Covers, seal the cover to the frame by pooling sealant in the bolt holes and applying a 3 ± 1 mm (0.12 ± 0.04 inch) continuous bead of sealant at the bolt holes pattern. Assemble cover within 3 minutes of sealant application.     |
2     | 6     | 266-3316 Bolts     | Torque to 40 ± 4 N·m (29.5 ± 3 lb ft).     |
3     | 6     | 287-4220 Shims     | The maximum gap between the load stops must be less than 2 mm (0.079 inch). Use the appropriate number of shims in order to obtain the required gap. A maximum of three shims per side should be used. If the gap is greater than 2 mm (0.08 inch) or the gap is less than 4 mm (0.16 inch), add one shim. If the gap is greater than 4 mm (0.16 inch) or the gap is less than 6 mm (0.24 inch), add two shims. If the gap is greater than 6 mm (0.27 inch) or the gap is less than 8 mm (0.32 inch), add three shims.     |
4     | 24     | 266-3316 Bolts     | Torque to 40 ± 4 N·m (29.5 ± 3 lb ft).     |
5     | 2     | 3S-9182 Magnetic Plugs     | Before assembly apply 5P-3413 Pipe Sealant to the threads. Torque to 75 N·m (55 lb ft).     |
Caterpillar Information System:
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - C3.3B
793F Series AC Off-Highway Truck Machine Systems Front Wheel Bearings - Install
793F Series AC Off-Highway Truck Machine Systems Front Wheel Bearings - Remove
789D Off-Highway Truck Gear Pump (Rear Axle Oil) - 2 Section
Relay Inspection and Replacement on Certain Gensets{4460, 4493} Relay Inspection and Replacement on Certain Gensets{4460, 4493}
789D Off-Highway Truck Gear Pump (Rear Axle Oil) - 1 Section
521B and 522B Track Feller Bunchers TA2 Technical Inspection{7000, 753T} 521B and 522B Track Feller Bunchers TA2 Technical Inspection{7000, 753T}
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Vibratory Control
R3000H Load Haul Dump Lift Arm Support Pins
R3000H Load Haul Dump Solenoid Valve (Parking Brake) - Test
R3000H Load Haul Dump Oil Filter (Pilot) - Replace
R3000H Load Haul Dump Differential Thrust Pin - Check/Adjust
2011/11/11 New High-Temperature Fasteners Are Used with the Exhaust Lines on C175 Off-Highway Truck Engines {1061, 7553}
789D Off-Highway Truck Oil Filter (Rear Axle)
2011/12/01 New Brake Pressure Warning Switch is Now Used on Certain Backhoe Loaders {4269}
420F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders MID 039 - CID 3709 - FMI 03
420F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders MID 039 - CID 3709 - FMI 05
420F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders MID 039 - CID 3709 - FMI 06
420F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders MID 039 - CID 2529 - FMI 02
789D Off-Highway Truck Flow Control and Relief Valve (Rear Axle Oil)
793F Off-Highway Truck Chassis Electronic Control System Command For Hauling General Information
2011/11/16 Improved Air Conditioner Compressor Bracket on 793F, 795F, and 797F Off-Highway Trucks {1802}
2011/11/23 A New Limit Switch Assembly for the Brake Pedal is Now Available on Certain M Series Motor Graders {1265, 3191, 4269}
793F Off-Highway Truck Chassis Electronic Control System Command For Hauling System Operation