Solenoid Valve (Pump Pressure) - Test
Show/hide table
| Required Tools | |||
| Tool | Part Number | Description | Qty |
| A | 198-4240 | Digital Pressure Indicator | 1 |
| B | 153-6267 | Elbow | 1 |
| C | 7X-2444 | Swivel Tee | 2 |
| D | 6V-3965 | Fitting As | 1 |
| E | 6V-9828 | Cap As | 1 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
 | |
| Illustration 1 | g01071386 |
(1) Pressure sensor (2) Pump pressure solenoid valve (3) Flushing and cooling control valve | |
This test will check solenoid valve (2) in order to determine if the solenoid valve is functioning correctly.
- Remove pressure sensor (1) from flushing and cooling control valve (3) .
- Refer to illustration 2 in order to assemble the following test equipment:
- Tool (C)
- Tool (D)
- Tool (E)
- Tool (C)
Show/hide table
 | |
| Illustration 2 | g01074930 |
(C) Cap (D) Fitting (E) Swivel Tee | |
- Install Tool (B) into flushing and cooling control valve (3) .
Show/hide table
 | |
| Illustration 3 | g01074621 |
- Install the test equipment that is shown in illustration 2 onto Tool (B) .
- Install pressure sensor (1) into the assembled tooling.
- Install Tooling (A) onto fitting (D) .
- Start the engine. Depress transmission modulator pedal (6) and shift the transmission direction and speed control to first speed forward. Set torque control lever (7) to the MINIMUM position. Move all wheel drive control (5) to the MANUAL position. Release transmission modulator pedal (6). Run the engine at high idle. The pressure gauge should be at 5500 ± 700 kPa (800 ± 100 psi).
Show/hide table
 | |
| Illustration 4 | g01070164 |
(5) All wheel drive control | |
Show/hide table
 | |
| Illustration 5 | g00861143 |
(6) Transmission modulator pedal | |
Show/hide table
 | |
| Illustration 6 | g00781613 |
- Move torque control lever (7) to the MAXIMUM position. Watch the pressure gauge as torque control lever (7) is moved. As torque control lever (7) moves toward the MAXIMUM position, the system pressure should increase. When torque control lever (7) is in the MAXIMUM position, the pressure gauge should be at 35200 ± 700 kPa (5100 ± 100 psi).
- Repeat Step 7 and Step 8 with the transmission and speed control in first speed reverse.
- Stop the machine and shut off the engine. If the pressure from the all wheel drive piston pump is not correct, check pump pressure solenoid valve (2). Pump pressure solenoid valve (2) may have a faulty solenoid, a sticking valve or a worn valve.
- Remove the test equipment from the machine.
Caterpillar Information System:
988H Wheel Loader Steering System Steering System Troubleshooting
PF-300C and PS-300C Pneumatic Compactors Machine System Water Spray System Troubleshooting
533 and 543 Wheel Feller Bunchers Transmission Gearbox Oil Sample - Obtain
16H Motor Grader Machine Systems Circle Drive - Disassemble
AP-800D and BG-230D Asphalt Pavers Time Delay Relay Control (Leveling)
16H Motor Grader Machine Systems Gerotor Motor (Circle Drive) - Install
AP-800D and BG-230D Asphalt Pavers Backup Alarm
988H Wheel Loader Power Train Transmission Hydraulic Control
12M Motor Grader Parking
16H Motor Grader Machine Systems Gerotor Motor (Circle Drive) - Remove
12M Motor Grader Engine Starting
AP-800D and BG-230D Asphalt Pavers Battery Disconnect Switch
AS2251 and AS2301 Screeds General Information
797B Off-Highway Truck Braking System Oil Cooler (Rear Brake)
797B Off-Highway Truck Braking System Oil Cooler (Fan Drive, Front Brake, Steering)
12M Motor Grader Stopping the Machine
C11 and C13 Engines Electronic Unit Injector Wiring
AP-800D and BG-230D Asphalt Pavers Tow Point Control
143H and 163H Motor Graders Wheel Bearing Oil (Front) - Change - If Equipped
143H and 163H Motor Graders Wheel Bearing Oil Level (Front) - Check - If Equipped
16H Motor Grader Machine Systems Circle Drive - Assemble
12M Motor Grader Moldboard Wear Strip - Inspect/Adjust/Replace
Comfort Series Seat For Caterpillar Machines Comfort Seat Controls
834H Wheel Dozer and 836H Landfill Compactor Power Train Relief Valve (Transmission Hydraulic Control)