Engine Starting
Show/hide table
 |
|
To prevent personal injury, be sure all personnel are clear of the machine. Sound the horn for several seconds before starting the engine. |
Show/hide table
|
|
Do not use ether. This machine is equipped with glow plugs. Using ether can create explosions or fires that can cause personal injury or death. Read and follow the engine starting procedure in the Operation and Maintenance Manual. |
Show/hide table
| NOTICE |
|---|
|
Do not crank the engine for more than 20 seconds. If the engine does not start, allow the starter to cool for two minutes before cranking again. The engine start switch must be turned to the OFF position before trying to restart. |
Show/hide table
| |
| Illustration 1 | g01052113 |
- Move propel control lever (1) to the NEUTRAL position.
- Push parking brake knob (2) downward.
Show/hide table
Illustration 2 g01052115 - Move throttle control (4) upward to the HIGH position.
- Turn key (5) to the ON position.
- Push the switch for the glow plug (3) upward for 20 seconds in order to heat the glow plugs.
Note: If the engine is already warm from previous operation, the glow plugs do not need to be heated.
- Crank the engine by turning key (5) to the START position. When the engine starts, release the key. Release the switch for the glow plug (3). Leave throttle control (4) in the HIGH position until the engine is running smoothly. Move throttle control (4) to the LOW position after the engine is running smoothly in order to allow the engine and the machine to warm-up properly.
Note: Refer to the Operation and Maintenance Manual, "Engine and Machine Warm-Up" for further information.
Caterpillar Information System:
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Axle - Install
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Piston Motor (Hydrostatic) - Install
CB-334E and CB-335E Vibratory Compactors Vibratory System Relief Valve (Intercircuit) - Test and Adjust
236B, 246B, 252B and 262B Skid Steer Loaders Hydraulic System Worksheets - Troubleshoot
740 EJECTOR Articulated Truck Maintenance Interval Schedule
735 Articulated Truck Maintenance Interval Schedule
PS-150C Paving Compactor Daily Inspection
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Machine Systems Air Conditioner and Heater - Assemble
CB-214E, CB-224E and CB-225E Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
CB-334E and CB-335E Vibratory Compactors Vibratory System Motor Support (Vibratory)
216B, 226B, 232B and 242B Skid Steer Loaders Power Train Solenoid Valve and Mounting (Parking Brake) - Remove and Install - One Speed
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Axle - Remove
216B, 226B, 232B and 242B Skid Steer Loaders Power Train Chain (Drive) - Remove
216B, 226B, 232B and 242B Skid Steer Loaders Power Train Chain (Drive) - Install
TK741, TK751 and TK752 Track Feller Bunchers Undercarriage - Check
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Axle - Disassemble
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Axle - Assemble
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Chain (Drive) Tension - Adjust
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing System
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing Motor
216B, 216B2, 226B, 226B2, 232B, 232B2, 242B and 242B2 Skid Steer Loaders Machine Systems Air Conditioner and Heater - Remove
2004/02/23 A New Filter for The Paving Compactor is Now Available {5068}
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
TK741, TK751 and TK752 Track Feller Bunchers Swing Gear - Lubricate